Battery Removal/Installation - Hitachi CG 36DL Bedienungsanleitung

1 Nylon head ............................................1
2 Cover ....................................................1
3 Hex. bar wrench 4 mm ..........................1
CG36DL
4 17×19 Combi box wrench .....................1
(NN)
5 Protective glass ....................................1
6 Shoulder belt ........................................1
7 Hanger belt ...........................................1
1 Battery (BSL3620) ................................1
2 Charger (UC36YRSL) ...........................1
3 Nylon head ............................................1
4 Cover ....................................................1
5 Hex. bar wrench 4 mm ..........................1
CG36DL(L)
(LBR)
6 17×19 Combi box wrench .....................1
7 Protective glass ....................................1
8 Shoulder belt ........................................1
9 Hanger belt ...........................................1
0 Battery cover ........................................1
1 Nylon head ............................................1
2 Cover ....................................................1
3 Hex. bar wrench 4 mm ..........................1
CG36DL(L)
4 17×19 Combi box wrench .....................1
(NN)
5 Protective glass ....................................1
6 Shoulder belt ........................................1
7 Hanger belt ...........................................1
1 Battery (BSL3620) ................................1
2 Charger (UC36YRSL) ...........................1
3 Nylon head ............................................1
4 Cover ....................................................1
CG36DAL
5 Hex. bar wrench 4 mm ..........................1
CG36DAL(L)
6 17×19 Combi box wrench .....................1
(LBR)
7 Protective glass ....................................1
8 Shoulder belt ........................................1
9 Hanger belt ...........................................1
0 Battery cover ........................................1
1 Nylon head ............................................1
2 Cover ....................................................1
3 Hex. bar wrench 4 mm ..........................1
CG36DAL
CG36DAL(L) 4 17×19 Combi box wrench .....................1
(NN)
5 Protective glass ....................................1
6 Shoulder belt ........................................1
7 Hanger belt ...........................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
◯ Battery
(BSL3620)
◯ Back pack power supply
(BL36200)
NOTE
For details of the operations, please see the BL36200
instruction manual.
When using the Cutting blade, have the Nut cover, Left
side M10 installation nut and Counter weight set ready for
installation.
◯ Nut cover (CG36DL only)
◯ Left side M10 installation nut (CG36DL only)
◯ Counter weight set (CG36DL only)
NOTE
For details of the operations, please see the Counter
weight set instruction manual.
Optional accessories are subject to change without notice.
APPLICATIONS
Trimming, scaling and mowing of weed.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the housing tightly and push the battery latches to
remove the battery (see Fig. 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see Fig.
2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to a receptacle.
When the power cord is connected, the charger's pilot
lamp will blink in red. (At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger until the line is
visible, as shown in Fig. 3 and 4.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the pilot lamp
will blink in red. (At 1-second intervals) (See Table 1)
English
(BSL3626)
○ Cutting blade
(CG36DL only)
17