Makita BTP140 Bedienungsanleitung Seite 5

Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model BTP130
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K) : 2.5 m/s
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model BTP140
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
ENG900-1
2
) : 11.5 m/s
h,ID
2
2
) : 5.5 m/s
h
2
2
) : 2.5 m/s or less
h,D
2
2
) : 9.0 m/s
h,ID
2
2
) : 10.0 m/s
h
2
2
) : 2.5 m/s or less
h,D
2
ENG901-1
ENH101-15
as the responsible
Cordless 4 Mode Impact Driver
Model No./ Type: BTP130,BTP140
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
000230
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
CORDLESS 4 MODE IMPACT
DRIVER SAFETY WARNINGS
1. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
3. Hold power
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. Hold power tool by insulated gripping surfaces,
when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
5
30.1.2009
Tomoyasu Kato
Director
tool by insulated
GEA010-1
GEB078-1
gripping