Technical Information - Bosch Intuvia Serie Originalbetriebsanleitung

Technical information

Type approval and jurdistiction
Our S-Pedelecs underwent a type approval at the German Department of Motor vehicles and are approved as motor vehicle. During
this process certain components were specified, which can be used with this vehicle. If this vehicle is not specified with these
components or - as described in the following - with alternatively authorized components, the type approval loses its validity.
Specialities of certain components of the motor vehicle S-Pedelec in comparison to conventional pedelec /
bicycle components
Several components of the S-Pedelec meet certain requirements of a motor vehicle of class L1e. They differ from conventional
components of pedelecs / bicycles. This results from the requirements of the respective EU regulation. In non-EU countries, like
e.g. Switzerland, several of these requirements might not be valid or other reuqirements might apply.
frame / fork
These load-carrying components of the S-Pedelec were costructed to bear the higher loads due to the higher speed in
comparison to a pedelec / bicycle.
licence plate holder
This part is constructed in a way so it can hold the plate according to the regulations (visibility, angle)
rear view mirror
This part is mandatory for motor vehicles. It is ECE-tested. You recognize an approved mirror by the E-marking.
brake lever
The brake levers for two-wheeled motor vehicles have a spherical balls at the ends. Conventional pedelec / bicycle
brake levers don't have these.
stand
The stand must pass several stability tests and furthermore must fold in automatically, as soon a it is completely
weight relieved.
lateral reflectors
They have to be orange and non-triangle and have to have a ECE type aproval. Their placing spot has to meet certain
visibiity requirements and must not be changed. You recognize an approved reflector by the E-marking
brake light
Since 2016 the brake light is mandatory for new type approvals.
licence plate lighting
The licence plate lighting is mandatory for all S-Pedelecs produced from 2016.
daytime running light / continuous lighting
A continuously activated daytime running light / continuous lighting is mandatory for all S-Pedelecs produced from
2016.
tyres
The tyres need an approval according to ECE R75. You recognize an approved tyre by the E-marking. For the possible
tyre sizes please see certificate of conformity.
6
Structural changes on your S-Pedelec
Since the S-Pedelec is a motor vehicle there are several restrictions concerning structural changes. Table 1 indicates which compo-
nents can be replaced under which conditions.
Table 1: S-Pedelec components and conditions for replacement
Following components on our S-Pedelec can be replaced ...
a) only by original compo- b) without approval
1
nents
frame grips
drive unit shift lever
saddle
battery seat post clamping ring
chain
headset
tube
tyres (size as in CoC document and others approved by
Winora; have to be type approved)
bell
carrier (max. +15% of original dimensions, position of licence
plate holder must remain the same)
Note: max. carrier load is 15kg
mud guard (must correspond with the original dimensions
+/- 15%)
Approval of alternative components by Winora-Staiger GmbH
If it is necessary to replace original components due to damage or wear we recommend to use orinigal components. Please contact
your specialist dealer. Winora-Staiger GmbH provides its specialist dealers with a list of orinigal specifications. When replacing
components from table 1a) it is required to only use original components.
Furthermore there is a possibility to use alternative components for parts of table 1b) and 1c). You are relatively free when choosing
parts from column b) of table 1, you have to use components approved by Winora-Staiger GmbH when replacing parts from column
c) of table 1.
Please contact your Haibike / Winora specialist dealer about this matter.
Winora-Staiger GmbH provides its specialist dealers a regularily updated list with approved components.
In case of infringement according to column a) or c) the vehicle loses its type approval and must not be used
anymore.
it is required that the parts meet at least bicycle standard ISO4210 and a professional mounting.
1
c) only with offiial approval of
Winora-Staiger GmbH
fork
handlebar, brakes
stem
gear shift
chainwheel
cranks
reflectors
front / rear light (must have
same illuminance and must be
mounted on the same position)
mirror
seat post
stand
rims/hubs/wheels
licence plater holder
7