Technical Data; Charging The Battery; Inserting And Removing The Battery - Bosch PowerTube 750 Originalbetriebsanleitung

English – 2
(4) PowerTube battery (pivot)
(5) Socket for charging connector
(6) Operation/battery charge indicator
(7) On/off button
(8) PowerTube battery safety restraint
(9) Locking mechanism
(10) Pull strap
(11) Axial rail
(12) PowerTube battery (axial)
(13) Upper axial PowerTube holder

Technical data

Li-ion battery
Product code
Product code
Rated voltage
Nominal capacity
Energy
Operating temperature
Storage temperature
Permitted charging temperature
range
Weight, approx.
Protection rating
Fitting
Ensure the battery is placed on clean surfaces only.
u
Avoid getting dirt, e.g. sand or soil, in the charging socket
and contacts in particular.
Testing the battery before using it for the first
time
Test the battery before charging it for the first time or using
it in your eBike.
To do this, press the on/off button (7) to switch the battery
on. If none of the LEDs on the battery charge indicator (6)
light up, the battery may be damaged.
If at least one (but not all) of the LEDs on the battery charge
indicator (6) lights up, the battery will need to be fully
charged before using it for the first time.
Do not charge or use batteries if they are damaged.
u
Contact an authorised bicycle dealer.

Charging the battery

A Bosch eBike battery must only be charged using an
u
original Bosch eBike charger.
0 275 007 3PX | (09.07.2021)
PowerTube 750
Horizontal BBP3770
Vertical BBP3771
V= 36
Ah 20.1
Wh 750
°C –5 to +40
°C +10 to +40
°C 0 to +40
kg 4.4
IP54
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using it for the first time.
To charge the battery, read and follow the instructions in the
operating manual for the charger.
The battery can be charged at any state of charge. Interrupt-
ing the charging process does not damage the battery.
The battery has a temperature monitoring function which
only allows it to be charged within a temperature range of
0 °C to 40 °C.
Do not reconnect the battery to the charger until it has
reached the correct charging temperature.
Battery charge indicator
The five green LEDs on the battery charge indicator (6) in-
dicate the battery's state of charge of when the battery is
switched on.
Each LED represents approximately 20 % of the charging ca-
pacity. When the battery is fully charged, all five LEDs will be
lit.
The battery's state of charge when switched on is also shown
on the display of the on-board computer. Read and follow
the instructions in the operating manuals for the drive unit
and on-board computer.
If the battery capacity is less than 5 %, all the LEDs on the
battery charge indicator (6) on the battery will go out. The
display function of the on-board computer, however, will
carry on working.
Once charging is complete, disconnect the battery from the
charger and the charger from the mains.

Inserting and removing the battery

Always switch off the battery and the eBike system
u
when inserting the battery into the holder or remov-
ing it from the holder.
Removing the PowerTube battery (pivot) (see figure A)
❶ To remove the PowerTube battery (4), open the
lock (2) using the key (1). The battery will be unlocked
and fall into the safety restraint (8).
❷ Press on the safety restraint from above. The battery
will be unlocked completely and fall into your hand.
Pull the battery out of the frame.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the PowerTube battery (pivot) (see figure B)
In order for the battery to be inserted, the key (1) must be
inserted into the lock (2) and the lock must be open.
If the temperature of the bat-
tery is outside this charging
range, three of the LEDs on
the battery charge indicator
(6) will flash. Disconnect the
battery from the charger and
let it acclimatise.
Bosch eBike Systems