Maintenance - Chicco Sprint Gebrauchsanleitung

CLEANING AND MAINTENANCE
CLEANING
Clean the fabric parts with a damp sponge and
neutral detergent. Please refer to the product's
care label.
Routinely wipe clean plastic parts with a soft
damp cloth.
Always dry the metal parts to prevent the forma-
tion of rust if the carrycot has come into contact
with water.

MAINTENANCE

Lubricate the moving parts only if necessary, with
a light application of a silicone based lubricant.
Always dry the metal parts to prevent the forma-
tion of rust. Do not submerge the carrycot in wa-
ter. Routinely wipe clean plastic parts with a soft
damp cloth. To avoid friction, ensure that the lock-
ing devices of the carrycot and pram are free from
dust or sand. Do not leave the product exposed to
the sun for a long period of time; it may cause the
fabric to fade.
CARRYCOT FEATURES
HOOD
The carrycot is equipped with a sun canopy and wind-
breaker that can be adjusted to various positions.
MOUNTING AND REMOVAL
1- Check that the clips located on the end of the
metal arch are properly fastened to the buttons
located on the fabric part. The buttons are prop-
erly fastened if the two ends of the metal arch
(fig 1) are easily visible.
2- Insert the two metal ends in the B and C sup-
ports located in the central part of the carrycot
until you hear a click (figure 2A); fasten the four
tabs of the rear arch (figure 2 B).
NB: The coupling system is located inside the
plastic B and C supports, the round button on the
supports serve only for removing the hood (see
point 3).
3- To remove the hood, first pull out the 4 tabs of
the rear arch (figure 3A) and then remove the
front arch by pushing the two buttons located
on the base of the locking device (fig. 3B).
WARNING: Improper removal of the hood could
result in the tabs breaking.
HOW TO USE THE HOOD
4- Inside the hood, between the visor and the first
segment, is a fabric ring that can be used for
hanging soft toys. It comes with handy hooks
(figure 4 A).
Warning- only use toys that have the following
Chicco codes: 60062, 60063, 60065
INTERNAL COVERING AND COVER
5- To fasten the internal covering to the carrycot:
Slip the plastic band located in the baby's
head zone between the styrofoam support
and the body of the carrycot; then fit the
fabric where the baby's feet will lie (diagram
5A). Fasten the cover in place using the two
side snap-buttons (diagram 5B) and insert the
eyelet over the relative hook where the baby's
feet will lie (diagram 5C). To guarantee ad-
ditional protection for your baby, thread the
two tape fasteners through the slots and close
the snap-buttons inside the hood, as seen in
diagram 5D.
The carrycot apron can be transformed into a
legcover for the stroller. Refer to the instruction
manual of the stroller for details related to assem-
bly of the legcover configuration.
ADJUSTABLE BACKREST -
COMFORT SYSTEM
6- The backrest of the carrycot can be adjusted
gradually. To lift or lower the backrest use the
wheel located on the outer part of the carrycot
near the baby's feet (figure 6).
WARNING: It is advisable to ventilate the carrycot
after prolonged use.
CARRYING HANDLE
7- The carrycot comes with a comfortable carrying
handle that can be adjusted in three positions
(fig. 7):
A) Transport
B) Middle
C) Rest
8- To put the handle in the vertical position, grasp
it in the centre and pull it upwards until you
hear a click (figure 8 A); to put the handle back
in the rest position press both buttons at the
base of the handle at the same time and then
turn it downwards (figure 8 B).
WARNING: Do not transport the carrycot with the
handle in the middle or rest position, but only with
the handle in carrying position.
WASHING
The hood, internal lining of the carrycot, and mat-
16