Maintenance - BFT Moovi 30 Installations- Und Gebrauchsanleitung

WARNING! Important safety instructions. Carefully read and comply with
the Warnings booklet and Instruction booklet that come with the product as
incorrect installation can cause injury to people and animals and damage to
property. They contain important information regarding safety, installation,
use and maintenance. Keep hold of instructions so that you can attach them
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product can
cause damage to persons, animals or things.
Warnings" lea et and "Instruction booklet" supplied with this
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children's reach.
reference.
this documentation could damage the product and be dangerous.
which the automated system is due to be installed.
ments of the following European Directives: 2004/108/EEC, 2006/95/EEC,
98/37/EEC, 99/05/EEC (and later amendments). For all countries outside
the EEC, it is advisable to comply with the above-mentioned standards,
in addition to any national standards in force, to achieve a good level of
safety.
ing structures (door, gates etc.), as well as from any deformation which
might occur during use.
European Directives: 2004/108/EEC, 2006/95/EEC, 98/37/EEC, 99/05/EEC
and subsequent amendments.
or omnipolar thermal-magnetic circuit breaker with a contact separation
of at least 3.5mm: the device must be connected upline from the power
supply terminals.
the power supply mains.
closure (doors, gates etc.) and all system components provided with an
earth terminal.
Keep mains connections well separated (at least a 2.5mm air gap) from
near the terminals or electrical connections, using devices such as cable
clamps.
be run together with the low voltage supply cable. Similarly, the power
cable's sheathing must only be stripped back in the immediate vicinity
of the terminal board.
appropriate equipment.
to protect the area from any danger caused by squashing, conveying and
shearing, according to and in compliance with the applicable directives
and technical standards.
from moving parts. Unless the control is key operated, it must be installed
at a height of at least 1.5 m and in a place where it cannot be reached by
the public
and that the safety and release systems are working properly.
and correct operation when other manufacturer's components are used.
INSTALLATION MANUAL
by the Company.
manual opening operation in case of emergency.
area.
order to avoid unintentional automation activation.
is not allowed.
prescribed by the EN 12978 Standard.
WARNING! For connection to the mains power supply, use a multicore
cable with a cross-section of at least 3x1.5mm
by the regulations mentioned above (by way of example, if the cable is
not protected, it must be rated H07 RN-F or higher, while if it is protected
it must be rated at least H05 VV-F with a cross-section of 3x1.5mm
Only use plastic raceways for both safety extra low voltage (SELV) cables
and low voltage (230 V) cables.
USE OF AUTOMATION
As automation can be remotely controlled and therefore not within sight, it is
WARNING! In case of any malfunction in the safety devices, take imme-diate
-
action and require the assistance of a specialised technician.
It is recommended to keep children at a safe distance from the automation
CONTROL
The automation system is used to obtain motorised access control. There are
di erent types of control (manual, remote, magnetic badge, mass detector
-
etc.) depending on the installation requirements and characteristics. For the
various control systems, see the relevant instructions. Do not use the auto-
mated device or put it into operation until the boom has been balanced.

MAINTENANCE

WARNING: before opening the door, the spring must be unloaded
(vertical boom). WARNING: Before carrying out any maintenance to the
installation, disconnect the mains power supply. The following points need
checking and maintenance:
- Electric edge. Carry out a periodical manual check to ensure that the edge
stops the bar in case of obstacles.
- Dismantle the gearmotor and replace the lubricating grease every two
years.
- When any operational malfunction is found, and not resolved, discon-
nect the mains power supply and request the assistance of a specialised
technician (installer). When the operator is out of order, activate the
emergency release (see Fig. Y), if necessary, so as to release the manual
boom opening and closing operations.
SCRAPPING
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular
risks or danger. In case of recovered materials, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
DISMANTLING
WARNING: before opening the door, the spring must be unloaded (verti-
cal boom). When the automation system is disassembled to be reassembled
on another site, proceed as follows:
- Disconnect the power supply and the entire electrical installation.
- Disassemble all the installation components.
- In the case where some of the components cannot be removed or are
damaged, they must be replaced.
Correct controller operation is only ensured when the data contained in
the present manual are observed. The Company is not to be held respon-
sible for any damage resulting from failure to observe the installation
standards and the instructions contained in the present manual.
The descriptions and illustrations contained in the present manual are
not binding. The Company reserves the right to make any alterations
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essential product fea-
tures unchanged, at any time and without undertaking to update the
present publication.
-
2 of the kind provided for
2 ).
15
MOOVI 30-50 - ALPHA BOM -