Werbung
FR
A
ImAGES
[1] Interface capteur LON WM
[2] Coller l'étiquette d'adresse du
sensor LON sur un plan ou sur
une liste
B
INSTALLATION
Choisir le meilleur emplacement: la
place doit être suffisante
[1] Installation du LON Sensor
Interface WM
[2] Montage sur un rail DIN
1.
Vertical (version montage
mural)
2.
Horizontal (version montage
mural)
C
CâBLAGE
[1] Gardez une distance minimale
[2] Outil pour tous les borniers
[3] Schéma de câblage du LON Sensor
Interface et Outside Sensor Box
D
mISE EN ROuTE/
CONFIGuRATION
[1] Pas de signal = information de
defaut ou mise en route
[2] LED LON clignotte toutes les
secondes = produit non commis-
sionné
[3] LED LON s'allume 2 secondes
après une courte pression sur le
bouton Reset/Prog = L'ID Neuron
est envoyé sur le bus LON
Câblage Cable Cavo
Connexion aux ...
Câble
Connection to ...
Cables
Connettere a ...
Cavo
LON Bus
2 x 2 x 0.8 mm
Sensor Bus RS485
Min.: 2 x 0.6 mm
Max.: 2 x 0.8 mm
Sensor A
Following sensor requirements
Sensor B
Following sensor requirements
Sensor C
Following sensor requirments
24V AC/DC
Min.: 2 x 1.5 mm
Max.: 2 x 2.5 mm
GB
A
PICTuRES
[1] LON Sensor Interface WM
[2] Attach the address label of the
LON Sensor Interface in a plan or
a list
B
mOuNTING
Choose the optimal location: flat and
large surface
[1] Mount the LON Sensor Interface
WM
[2] Mount the DIN rail version
1.
Vertical (wall mounted ver-
sion)
2.
Horizontal (wall mounted
version)
C
WIRING
[1] Keep the minimum distance
[2] Tool for all terminals
[3] Wiring diagram LON Sensor
Interface and Outside Sensor Box
D
COmmISSIONING/
CONFIGuRATION
[1] No signal = default delivery
status or commissioned
[2] LON LED blinks in 1 second inter-
valls = device uncommissioned
[3] LON LED shines for 2 seconds after
a short press of the Reset/Prog
button = neuron ID is sent on the
LON bus
Paires torsadées
Twisted pairs
Doppino
Required, following LON topology guidelines
2
/19 AWG
Recommended
2
/18 AWG
2
Following sensor requirments
Following sensor requirments
Following sensor requirments
/16 AWG
2
/13 AWG
2
IT
A
ImmAGINI
[1] LON Sensor Interface WM
[2] Applicare l'etichetta dell'indirizzo
ID del LON Sensor Interface in un
progetto o in una lista
B
mONTAGGIO
Scegliere il luogo più adatto per il
montaggio
[1] Montaggio del LON Sensor
Interface WM
[2] Montaggio della versione in
guida DIN
1.
Verticale (montaggio a muro )
2.
Orizzontale (montaggio a
muro)
C
COLLEGAmENTO ELETTRICO
[1] Tenere la distanza minima
[2] Strumenti per tutte le connessio-
ni
[3] Schema di cablaggio LON Sensor
Interface e Outside Sensor Box
D
VERIFICA/CONFIGuRAzIONE
[1] Nessun segnale = impostazioni
di fabbrica o non indirizzato
[2] Il led del LON lampeggia ad in-
tervalli di 1 secondo = dispositivo
non indirizzato
[3] Il led del LON si accende per 2 se-
condi dopo una breve pressione
del tasto Reset/Prog = l'indirizzo
ID viene inviato sul bus LON
Max. Länge
Maks. længde
Max. etäisyys
500 m
animeo LON SENSOR INTERFACE . REF. 5062104 -
5/8
Werbung
