Distance To Combustible Material - Nordpeis Q-23FL Montageanleitung

3. Distance to combustible material

Firewall
(FIG 1).
When connecting a steel chimney to the top outlet use
the security distances required by the manufacturer.
material, such as linoleum, carpets etc. must be
The insert expands when in use, and for this
reason the surround must NEVER rest on the
Warning: If the requirements for ventilation are
insert must neither rest on the bench plate
NOT complied with, the cooling airflow around
the product will be considerably reduced and
the product can overheat.
This can cause a fire.
Before the insert is removed from the pallet, remove the
Ensure that the safety distances are fulfilled.
accessories in the combustion chamber. To acess the
combustion chamber, do as follows:
1. Loosen the transport safety from the counterweight
and loosen the screw fastening the transport safety to
the product. Push the transport safety away from the
Important! When placing the insert on a
counterweight FIG 3A.
combustible floor, a steel plate of at least 0.7mm
must cover the entire floor surface inside the
2. Make sure both wires are in place before opening the
surround. Any flooring made of combustible
door FIG 3B
removed from underneath the steel plate.
3. Remove alle loose accessories from the combustion
chamber. Use the list of contents to make sure all parts
are included. Before lifting the product of the pallet,
secure the counterweight with the transport safety.
insert, but have a gap of about 3 mm. The
4. The insert is placed on two rails on top of the pallet.
or against the sides. It is recommended to
In order to remove it from the rails and pallet, loosen
dry stack the surround in order to adjust the
the screws and remove the brackets holding it in place.
insert prior to perforating the chimney for the
Before lifting the insert of the pallet, fasten the screws
flue connection.
removed from the legs FIG 2.
Operational control
4. Assembly
When the insert is in an upright position, and prior to
mounting the surround, check that all
functions are easy to use and appear satisfactory.
1. Adjust the legs. Make sure the insert is level.
2. Loosen the transport safety. Make sure the
wires holding the door are in place.
3. Make sure the door can be opened and closed
properly.
A
If the insert is connected to the smokepipe
sideways, attach the small radiation shield around the
pulley closest to the smokepipe.
Left position = closed
Right position = open
Attention! The pulleys on each side of the door are
coated with special heat resistant grease. If a new
grease is needed, contact one of our dealers to
To make the door self closing, do as follows;
make sure the right type of grease is used.
holding the weights in place outwards FIG 4(A)
Pulley radiation shield FIG 8
3. Carefully push the clamps back in place.
If it becomes necessary to clean the glass, pull out the
two small handles above the door to keep it in place
FIG 5A. Pull out the lock handle on the left side of the
lock the handle on the left side of the door before
pushing the two small handles back in place.
Air vent control
Air vent control
Radiation shields, rear and around smoke collar.
separate shield around the smoke collar(FIG 6-7). To
utilize the rear or side connection, remove the cut in
the radiation shield. To keep the smoke collar radia-
Self-closing door
tion shield in place, push the upper and lower cuts in
towards the smokepipe
1. Use a flat screwdriver to move the three clamps
2. Remove the weight fittet with a handle FIG 4(B)
GB
Cleaning the glass FIG 5A-B
door and open the door. After cleaning the glass, first
Caution!! Be careful when opening the door
sideways. Some surrounds have marble/waxed
concrete parts and grates quite close to the door
and both the door and surrounding parts may
sustain damage if carelessly operated.
The insert is fitted with a rear radiation shield and a
B
Fully to the right
Igition
Ignition position
(nede til høyre)
19