Coltene BioSonic UC125 Benutzerhandbuch Seite 3

Owner's Guide
An Essential Part of Your Infection
Control System
Congratulations on your purchase of a
BioSonic Ultrasonic Cleaner- the finest,
®
most efficient and most popular ultrasonic
cleaning system in dentistry.
Developed specifically for the dental
industry, BioSonic units feature unique
product design to optimize time and safety
in the office or laboratory.
BioSonic is a total ultrasonic cleaning system,
with a full line of cleaning solutions and
unit accessories which provide you with the
flexibility to efficiently clean instruments,
prostheses and other appliances.
What is Ultrasonic Cleaning?
Ultrasonic Cleaning is a process created
by high frequency soundwaves. The
soundwaves, enhanced
formulated cleaning solutions, create
high energy cavitation. During cavitation,
millions of tiny bubbles form and then
collapse or "implode," releasing enormous
amounts of energy and shock waves which
scour the surface of instruments, appliances
and other devices placed in the cleaning
solution. This powerful scouring action
reaches into minute crevices, which manual
brushing cannot reach. The combination of
energy and specially formulated solutions
make ultrasonic cleaning the most effective
method for removing gross and microscopic
debris.
Intended Use: The Biosonic ® UC125
Ultrasonic Cleaner is intended for cleaning
medical instruments by the emission of
high frequency soundwaves.
I. Unpacking
1. Remove your BioSonic unit from the
shipping container and inspect the unit
for any possible damage which may
have occurred during shipping.
2. Check the serial number of the unit
(found on either the under side or
rear of the unit) with the number on
the shipping carton. If they are not
identical, contact your dealer.
3. Fill out the warranty card and mail
to Coltène/Whaledent Inc. within
10 days of receipt.
4. Select your desired location for the
cleaner. It should be in close proximity
to a sink or to waste lines to facilitate
draining. The hose supplied with the
unit will allow you to place the unit
on either side of the sink or connect
directly to the waste line.
5. Connect one end of the hose to the
drain valve (Fig. 1) and place the other
end in the sink. If desired, have your
plumber connect the hose directly to
the waste line with the appropriate
fittings.
II. Setup Instructions
1. CONNECT THE DISPLAY. Attach the
connector on the front of the display
module to the connector on the back
top right-hand corner of the unit.
Using the supplied hex L-key tool,
install two screws (included) to secure
the Liquid Crystal Display (LCD).
2. PLUG IN THE UNIT. Attach the UC125's
electrical cord at the lower back of
the unit and plug into a three-wire
by specially
grounded AC outlet (in accordance with
local regulations). It is recommended
that the unit be plugged into a Ground
Fault Circuit Interrupter (GFCI) outlet.
3. SELECT A LANGUAGE. Using the arrow
keys on the LCD display, select the
language code for your appropriate
region. If you are unsure which code
relates to your office, see the front
page of the Owner's Guide and choose
the language you use in your office.
Use the arrow keys to highlight the
appropriate code. (The code will flash
when it is selected.) Press ENTER to
accept.
4. SET THE CLOCK. Use the arrow keys
to set the time on the UC125. Four
numbers will appear on the screen. Use
the "+" arrow key to increase the digit;
use the "-" arrow key to decrease the
digit. Press ENTER to accept.
NOTE: Users who select English must
choose AM or PM and press ENTER to
continue.
5. SET THE DATE. Use the arrow keys to
set the date on the UC125. "01/01/00"
will appear on the screen. Each number
will flash when it is selected. Use the
"+" arrow key to increase the digit;
use the "-" arrow key to decrease the
digit. Press ENTER to accept.
• US/Date Format (MM/DD/YY)
• International Date Format (DD/MM/
YY)
6. SETUP COMPLETE. The display will
now show the message "Setup
Complete" in the language of your
choice. Simply fill the tank of the
UC125 with BioSonic Solution and
water. You are ready to go! Enjoy
your UC125! The default screen will
now display on the LCD screen,
indicating that your unit is properly
programmed.
NOTE: If a mistake is made while
programming the LCD, a user may repeat
this process by pressing and holding the "-"
arrow key for 5 seconds.
MEMORY FEATURE: In the event of a
power failure, your UC125 is equipped
with a back-up power supply that will
retain your programming information. This
supply will be capable of storing user
settings for a minimum of 12 days before
it is again necessary to reprogram the unit.
III. Filling Instructions
1. Insure that the blue drain handle
(Fig. 2) is fully rotated clockwise to
the "Close" position. Fill the unit with
warm water to the fill line indicator
(Fig. 3).
2. Pour the required amount of ultrasonic
cleaning solution (either BioSonic
General Purpose UC30, BioSonic
Germicidal Cleaner UC38/UC42 or
BioSonic Enzymatic Ultrasonic Cleaner
UC32) and water into the tank. Press
the solution reset key.
3. Change the solution in the tank
daily, or sooner if it appears soiled or
discolored. When beakers are used,
change the solution in the beaker after
each use.
4. Drain unit by fully rotating the blue
drain handle counter-clockwise to the
"Open" position and allow solution
to empty into sink or waste system.
Rinse tank and fully rotate the blue
drain handle clockwise to the "Close"
position. Never drain tank by manually
discarding solution as this may cause
the unit to stop working properly.
NOTE: Never operate the unit without
solution. Operating a dry tank will void
the warranty. Do not place objects directly
on bottom of tank. Always use accessory
baskets, cassette racks or beakers.
IV. Degassing Instructions
Degassing the solution eliminates large air
bubbles that interfere with the cleaning
3