Hama EWS-280 Bedienungsanleitung Seite 5

Note – Time settings
• The search process takes about 3-5 minutes. If the search fails, it ends and is
repeated at the next clock hour. The radio symbol (4) disappears.
• In the meantime, however, you can set the time and the date manually.
• The clock automatically continues to search for the DCF signal every hour.
If the signal is received successfully, the manually set time and date are
overwritten. The clock automatically continues to search for the DCF signal
every hour. If the signal is received successfully, the manually set time and
date are overwritten.
• Press and hold the p button (14) again for approx. 3 seconds to stop the
manual search. The radio symbol (4) disappears.
Note – Summer time
The clock automatically switches to summer time.
long as summer time is activated.
Manually setting the date/time
Note – Time and time zone
• Press the MODE button (13) repeatedly to switch between the following
displays:
• Time display with seconds, time display with day of the week, time display
with day of the week (adjusted for time zone), time display with seconds
(adjusted for time zone)
• The time zone symbol (6) is displayed when the time has been adjusted
according to the time zone.
• Press and hold the p button (18) for approx. 3 seconds to stop the search
for the DCF signal. The wireless icon (4) disappears and you can set the time
manually.
• Repeatedly press the MODE button (13) until the time zone symbol (6) is no
longer displayed.
• Press and hold the MODE button (13) for approx. 3 seconds to make the
following settings one after the other:
• Day of the week (10)
• Year (5)
• Month (7)
• Day (7)
• D/M – M/D (7) display
• 12/24-hour format (5)
• Hours (5)
• Minutes (5)
• To select individual values, press the p button (14) or the q button (17) and
confirm each selection by pressing the MODE button (13).
• Press the MODE button (13) immediately to adopt the set value displayed and
skip ahead.
• If you do not make an entry for 2 minutes, you automatically exit the setup
mode.
Note – Day of the week
You can choose from German (DE), English (EN), Swedish (SW), Dutch (DU),
Spanish (SP), Italian (IT) or French (FR) for the day of the week display.
4
Setting the time zone
• Repeatedly press the MODE button (13) until the time zone symbol (6) is displayed.
• Press and hold the MODE button (13) for approx. 3 seconds to set the required time
• To select individual values, press the p button (14) or the q button (17) and
• If you do not make an entry for 2 minutes, you automatically exit the setup mode.
appears on the display as
Alarm
• Repeatedly press the ALARM button (12) to display the different alarms.
• The alarm symbols (11)
• Press and hold the ALARM button (12) for approx. 3 seconds to set the time of
• Press the p button (14) or theq button (17) to select the hour for the alarm
• Repeat the process to set the minutes for the alarm time.
• Press the ALARM button (12) again to set the other alarm mode as well or to
• If you do not make an entry for 2 minutes, you automatically exit the setup
• In the corresponding display, press the
• If the alarm is triggered, the alarm symbol (11) will begin to flash and an alarm
• Press the alarm button (12) to stop the alarm. Otherwise, it will stop
6.3. Weather
Celsius/Fahrenheit
• Press the °C/°F button (15) to choose between °C and °F for the temperature
Note – Time zone
• The DCF signal can be received over long distances, but always transmits the
current Central European Time in Germany. Make sure you account for the
time difference in countries with another time zone.
• If you are in Moscow, the time is 3 hours later than in Germany. This means
that you should set +3 for the time zone. The clock then automatically sets
the time to 3 hours after the DCF signal received or relative to the manually
set time.
zone difference.
confirm each selection by pressing the MODE button (13).
/
alarm times or OFF.
the alarm displayed. The hours display begins to flash.
time and confirm your selection by pressing the ALARM button (12). The
minutes display begins to flash.
return to the time display (5).
mode.
ote – Alarm
N
• When activated, the weekday alarm only triggers an alarm on weekdays
(Monday to Friday). The alarm symbol (10)
activated.
• When activated, the once-only alarm only triggers an alarm once. The
alarm symbol (10) is displayed if this alarm is activated. This alarm is
automatically deactivated after the alarm has sounded.
activate/deactivate the corresponding alarm.
The alarm symbol (10) will appear/not appear.
will sound.
automatically after 2 minutes.
display
are displayed along with the corresponding
is displayed if this alarm is
-button (14) or the -button (17) to