Kenwood FHM15 Bedienungsanleitungen Seite 8

weighing function/countdown timer
Your food processor is fitted with a built in weighing function
to allow ingredients to be weighed straight into the bowl or
blender goblet.
The Maximum weighing capacity is 3kg. This is the total
l
weight of all the ingredients including the weight of the bowl
or goblet.
to use the weighing function
1 Always fit the bowl, detachable drive shaft and attachment
or blender goblet onto the power unit before adding
ingredients.
2 Plug in – the display screen will
remain blank until the speed
control is turned to 'ON'.
3 Turn to 'ON' the display screen
will light up.
4 Press the (kg/lb) button to select
either grams or ounces. The
display will default to kg/g when
first switched on.
The unit weighs in 1g increments
l
and teaspoon/tablespoon
measures are recommended for
weighing small quantities.
5 Check the display shows '0', if not, zero by pressing the
ZERO button. Then weigh the required ingredients straight
into the bowl or goblet. After the weight is displayed, press
the ZERO button and the display will return to '0'. Add the
next ingredients and that weight will be displayed. Repeat
until all ingredients are weighed.
To zero press the ZERO button once.
l
6 Fit the lid and select a speed to operate the processor.
During operation the display screen will show the count up
l
time.
To swap to the weighing function, turn to the 'ON' position
l
and whilst the timer is paused hold the kg/lb button down
for 2 seconds.
If the display is not zeroed and either the ingredients or the
l
bowl/attachment/lid are removed the display will flash
(----) to represent a minus reading. Press the ZERO button
to reset.
The weight of any additional ingredients added down the
l
feed tube whilst the processor is running will not be shown
on the display screen.
weighing tray
b
A removable weighing tray
is supplied for weighing
ingredients without the
bowl or blender.
To use, place the tray on
top of the power unit and
turn clockwise to secure
in place.
To remove just turn anti-
clockwise and lift off.
Count up timer
During operation the display screen will automatically
l
operate as a count up timer.
The timer will count up in seconds to 10 minutes and
l
will pause whenever the speed control is turned to 'ON'
position.
To reset the timer to zero press the ZERO button.
l
auto switch off
The display screen will turn on whenever the speed control
l
is in the 'ON' position, unless the auto switch off has
activated.
The auto switch off will activate if the appliance is left
l
plugged in without operating for more than 30 minutes. To
re-activate press either the ZERO button or turn the speed
control off 'O' and then back to the 'ON' position.
important
Do not overload by exceeding the maximum weighing
l
capacity of 3kg. The display will show [o – Ld] if the
weighing function is overloaded.
Do not subject the power unit to excessive force as this may
l
damage the weighing sensor.
Always place the processor on a dry flat surface prior to
l
weighing.
Do not move the power unit during operation of the
l
weighing function.
to use your blender
1 Fit the sealing ring
b
the seal is located correctly in the grooved area.
Leaking will occur if the seal is damaged or
l
incorrectly fitted.
2 Hold the underside of the blade assembly
blades into the goblet - turn anti-clockwise until it is secure
.
4
3 Put your ingredients into the goblet.
4 Fit the lid onto the goblet and turn clockwise
clicks. Fit the filler cap.
5 Place the blender onto the power unit by placing the handle
to the right hand side and turn forward
The blender will not operate if not fitted to the
l
interlock correctly. Check that the handle is
situated to the right hand front corner.
The blender will not operate if incorrectly
assembled.
6 Select a speed (refer to the recommended speed chart) or
use the pulse control.
5
(if supplied)
into the blade assembly
bq
and insert the
bq
until it
5
until it locks.
6
- ensuring