Specific Safety Rules - Makita DA4000LR Betriebsanleitung

ENGLISH
1 High
2 Low
3 Chuck key
4 Drill chuck
5 Hex wrench
6 Loosen
7 Angle housing
SPECIFICATIONS
Model
Drilling capacities
Steel ................................................................... 13 mm
Wood .................................................................. 38 mm
-1
No load speed (min )
High ................................................................... 0 – 900
Low .................................................................... 0 – 400
Overall length ...................................................... 413 mm
Net weight............................................................... 3.7 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the opeator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
8. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
Explanation of general view
8 Joint
9 Socket
10 Bolt
11 HIGH
12 LOW
13 High speed operation
14 Two faces
WARNING:
MISUSE or failure to follow the safety rules stated in
DA4000LR
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing angle attachment
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the angle attach-
ment.
The angle head has a spindle on each end. For higher
speed operation, attach the drill chuck to the end marked
"HIGH". The higher speed is better suited for drilling
smaller diameter holes. For lower speed operation,
attach the drill chuck to the end marked "LOW". The
lower speed is best utilized for drilling larger diameter
holes. (Fig. 1)
The tool is factory assembled with the chuck on spindle
end marked "HIGH".
To change to the "LOW" speed, proceed as follows:
To remove the drill chuck, first open the chuck jaws com-
pletely and place the chuck key in one of the key holes.
(Fig. 2)
GEB001-2
Remove the chuck remaining bolt through the chuck
opening by turning it counterclockwise with the hex
wrench. (Fig. 3)
CAUTION:
The drill chuck and the bolt are assembled each other.
Turn the bolt counterclockwise about 10 times so that
they can be removed together.
Loosen the bolts of the joint by the hex wrench and
remove the angle housing, the joint and the socket.
(Fig. 4)
To install the socket and the joint, fit the socket to the
spindle so that the two faces are fitted perfectly. Then
install the joint. For higher speed operation, fit the angle
housing marked "LOW" to the joint.
For lower speed operation, fit the angle housing marked
"HIGH" to the joint. (Fig. 5)
Rotate the angle housing to the desired position. Tighten
the bolt with the hex wrench firmly. And retighten the
another bolt firmly again. (Fig. 6)
15 Spindle
16 Tighten
17 Switch trigger
18 Reversing switch lever
19 Limit mark
20 Brush holder cap
21 Screwdriver
5