Master/Slave Operation - EuroLite LED PSU-8A Bedienungsanleitung

MODE button SETUP button
Address setting
DMX MODE
Channel setting
Select LED tube
Red dimmer
DIMMER
Green dimmer
MODE
Blue dimmer
Strobe effect
Select program
SOUND
Sensitivity
MODE
setting
Fade programs
AUTO
Color change
MODE
Speed setting
STATIC
Select LED tube
COLOR
SELECT
Color select
MODE
Strobe effect
Display on/off
LCD backlight
brightness
OTHER
IR remote
SETTINGS
function On/Off
Selecting
LED Tube type
Default
IP address
setting
ART-NET
CONTROL
Subnet mask
MODE
setting
DMX universe
output setting
Please note: After the controller IP address has been changed, you have to restart the controller to make
this change effective.

Master/Slave operation

The master/slave operation enables that several devices can be synchronized and controlled by one master
device.
On the rear panel of the LED PSU-8A Artnet/DMX you can find an XLR-jack (DMX Out) and an XLR-plug
(DMX In), which can be used for connecting several devices.
Choose the device which is to control the effects. This device then works as master device and controls all
other slave devices, which are to be connected to the master device via a DMX cable. Connect the DMX
OUT jack with the DMX IN plug of the next device.
UP/DOWN buttons
DMX MODE ADDR:XXX
DMX MODE CHAN: 005
DMX MODE CHAN: 007
DMX MODE CHAN: 026
MANUAL TUBE:ALL/XX
MANUAL TUBE:01~08
MANUAL RED:XXX
MANUAL GREN:XXX
MANUAL BLUE:XXX
MANUAL FLASH:XX
SOUND PROG:XX
SOUND SENS:XX
AUTO RUN FADE:XX
AUTO RUN JUMP:XX
AUTO RUN SPEED:XX
STATIC TUBE:ALL/XX
STATIC TUBE:01~08
STATIC CLR:XX
STATIC FLASH:XX
OPTION BLGT:ON
OPTION BLGT:OFF
OPTION BRCO:XXX
OPTION IR: ON
OPTION IR: OFF
OPTION TUBES: 27
OPTION TUBES: 54
OPTION SYSRESET
NET MODE IP0:×××
NET MODE IP1:×××
NET MODE IP2:×××
NET MODE IP3:×××
NET MODE SW0:×××
NET MODE SW1:×××
NET MODE SW2:×××
NET MODE SW3:×××
NET MODE U1:×××××
NET MODE U2:×××××
NET MODE U3:×××××
NET MODE U4:×××××
25/32
Sets the DMX starting address
5-channel mode
7-channel mode
26-channel mode
Dims all the LED tubes
Dims the corresponding single LED tube
Red intensity from 000 - 255
Green intensity from 000 - 255
Blue intensity from 000 - 255
Speed steps 00 ~ 15 with increasing speed
Select from 24 built-in sound controlled programs
Steps 01 ~ 08 with increasing sensitivity.
Select from the 24 built-in fade programs
Select from the 24 built-in color change programs
Speed steps 01 ~ 16 with increasing speed
Sets one static color on all the LED tubes
Sets a static color on the corresponding single LED tube
Select from 7 static colors 00 ~ 07
Speed steps 00 ~ 15 with increasing speed
Display always on
Display off after 20 seconds of no operation
Adjusts the brightness of the LCD backlight
IR remote function on
IR remote function off
Controls 1 meter tubes
Controls 2 meter tubes
When display backlight flickers, press UP/DOWN
buttons at the same time to initialize factory settings
Setting the IP address section 1
Setting the IP address section 2
Setting the IP address section 3
Setting the IP address section 4
Setting the subnet mask section 1
Setting the subnet mask section 2
Setting the subnet mask section 3
Setting the subnet mask section 4
Setting the DMX universe output section 1
Setting the DMX universe output section 2
Setting the DMX universe output section 3
Setting the DMX universe output section 4
Function
00090356, Version 1.0