Operation; Maintenance - Elica Glide Montage- Und Gebrauchsanweisung

Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour screen
6. Vapour screen guides
7. Air exit
8. Fairing (supplied in two sizes)
9. Fixing points for cabinet
10. Inspection door for the suction group (ACCESS
ALLOWED ONLY BY A QUALIFIED TECHNICIAN).

Operation

The cooker hood may be supplied with an automatic switching
on/off device.
Closing the drawer the cooker hood switches off; opening the
drawer the cooker hood switches on.
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Functioning - Model with display
A B C
A - Lighting, on/off.
B - Fan off (Stand by)
C - Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the cooker hood for a
established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D - Display showing:
• Fan speed (1-3-P).
• Change grease filters (grease filter saturation
indicator - F)
After washing the anti-grease filter, depress knob
B for about 3 seconds. The letter F will disappear
from the display.
• Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob B
for about 3 seconds. The letter C will disappear from
the display.
• When the led in the lower right side is on,
indicates that the cooker hood is ready for operation
("standby" position), the flashing LED indicates that
the timer has been activated for selected speed.
D E F
Warning!
The active carbon filter saturation function is not
activated.
In order to activate the carbon filter saturation indicator,
press buttons E and F simultaneously for 3 seconds.
Initially, only letter F will fbe displayed, then after the 3
seconds have passed, letter C will be displayed as well,
indicating that the carbon filter saturation control system
is active.
To switch off the system, re-press the same two buttons:
letter C appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E - Knob to decrease the speed: from intensive speed P to
speed level 1.
F - Knob to increase (standby) speed to intensive speed P.
Attention! Intensive speed P has a duration of 5 minutes
after which the cooker hood automatically sets the speed
to level 2 (suction power).
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning!
Always press the fan off button A before disconnecting the
hood from the mains supply.
Functioning – Model with Keyboard
B
A
A. on/off light switch
B. on/off aspiration switch and minimum power selection
B+C. medium power selection aspiration switch
B+D. maximum power selection aspiration switch

Maintenance

ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend oserving these instructions.
it
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
12
D
C