Elica Glide Montage- Und Gebrauchsanweisung Seite 11

located in an accessible area apply a double pole switch in
accordance with standards which assures the complete
disconnection of the mains under conditions relating to over-
current category III, in accordance with installation
instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Warning! Power cable replacement must be undertaken by
the authorised service assistance centre or similar qualified
person.
Mounting
Preliminary information for installation of the hood:
Disconnect the cooker hood from the electrical mains during
the electrical connection phase.
The cooker hood is designed for installation inside a wall
cabinet.
It is recommended to install the cooker hood only inside a
cabinet of suitable dimensions.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Do not fix chimney flue to furniture or fly over shelves unless
the chimney flue can be easily removed, in case maintenance
is ever required.
Refer to figure 2 for useful information for safe installation and
for eventual perforations to perform at the base of the cabinet
for air evacuation, for the
connection cable and to permit to access the electronic card
that controls the cooker hood operation (ACCESS ALLOWED
ONLY BY QUALIFIED TECHNICIAN).
Warning! The cooker hood is supplied with 4 side spacers (2
for the right side and 2 for the left side), these are useful when
the width of the housing cabinet for the cooker hood motor
body is wider than 6mm. In this instance the spacers should
be mounted outside the cooker hood body corresponding to
the perforations for the cabinet fixing screws (Fig. 2-A)
1. Measure the cabinet depth (consider also the cabinet
door) as for a depth of up to 315mm will require the
mounting of 37mm fairing, and for measurements over
315mm will require the mounting of 75mm fairing.
The fairing C should be fixed to the cooker hood body
brackets using 4 screws (fig. 3).
2. Fix the air exit connector B above the cooker hood body
(fig. 3).
Only for Filter Version:
place the deflector F on the exit connector.
Fix the filter holder frame inside the cooker hood, firstly
above on the rings R set in the body, then on the base
using the two screws S (fig. 3).
3. Apply the supplied template first to the right and then to
the left (fig. 4.1) or, if supplied, apply the apposite
template to the wall (fig. 4.2 – only in case of models
conceived for fixing to the wall) and making holes as
indicated (for the templates for fixing to the wall units 3
dead holes are indicated, 2 of Ø 2mm and one of Ø
5mm, while for the template for fixing to the wall, 2 holes
of Ø 8mm).
ATTENTION!
UNIT
The lower and back edge of the template must
correspond to the lower edge of the wall unit.
ATTENTION! TEMPLATE AND FIXING TO WALL
The lower edge of the template must correspond to the
lower edge of the hood.
Only for models with fixing hooks: make the holes and fix
two hooks with screws and dowels
(J – fig. 4.2).
Install the two supplied Y brackets with two screws and
washer each onto the upper side of the hood (fig.4.2).
4. Insert the body of the hood inside the wall unit (fig. 5).
This can remain temporarily in position:
a) in case of fixing to the wall unit, using lateral springs
D to imbed into the Ø 5mm dead holes (to do this, press
the lateral springs towards the inside of the body of the
hood using a screwdriver as a liver.
b) in case of fixing to the wall, with the hooks and the
brackets (the bracket have adjustable positioning
screws).
ATTENTION!
Check that the electric cable and the smoke outlet are
accessible to facilitate successive connections (and for
technical assistance and maintenance interventions).
5. Check that guides G (fig. 6) are perfectly parallel to the
lower edge of the wall unit, after which, ONLY in the case
of fixing to the wall unit, definitely fix the body of the hood
to the sides of the wall unit with 4 screws (E – fig. 6 – two
per side). The screws are to be inserted from inside the
body of the hood on the wall unit in correspondence
with the 4 Ø 2mm blind holes previously made (see
operation 3).
6. Insert the cooker hood cabinet base on the bracket
guides G then carry out the electrical connections of the
cooker hood cabinet base to the casing (fig. 7).
7. Regulate the cooker hood cabinet base in order that the
frontal part is in line with the cabinet (H - fig. 8) then block
the cooker hood cabinet base using 2 screws (one per
side - L - fig. 8 – To insert these two screws you will need
to remove the filter grill and screw them on the inserts
that are fixed on the mantel guides).
8. Fix the cooker hood cabinet base to the cabinet using the
2 screws M (fig. 8), use 2 of 4 perforations available and
check that the screws are fixed to the cabinet.
9. Remount the grease filter, connect the cooker hood to
the electrical network and to the discharge tube, check
the perfect operation of the cooker hood.
11
TEMPLATE AND FIXING TO WALL