Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CONTROLS AND FUNCTIONS
1)
"POWER" MASTER SWITCH
This switch permits turning the speaker on and off.
2)
"MAINS FUSE" FUSE CARRIER
Mains fuse housing.
3)
"MAINS INPUT" POWER SOCKET
For connecting the power cable provided.
The connector used for mains connection is a POWER CON® (blue)
4)
COOLING GRILLE
These grilles permit cooling the amplifier during operation.
Do not block accesses and clean the grilles whenever necessary to ensure correct
air circulation.
5)
" BALANCED INPUT" INPUT CONNECTOR
Balanced input at line level (0 dBu).
It is able to accept "XLR" sockets.
6)
"LINK" OUTPUT CONNECTOR
The "XLR" connector connected in parallel with input (5) can be used to send the
input audio signal to another amplified speaker.
7)
"BALANCED X-OVER OUTPUT" OUTPUT CONNECTOR
Internal crossover balanced output. The signal from this output can be sent to any
other amplified speaker.
The crossover frequency can be selected by means of the "SUB X-OVER" switch (8).
8)
"SUB X -OVER " SWITCH
This switch permits selection of crossover frequency between the sub woofer and
the speakers connected to the "BALANCED X-OVER OUTPUT" connector.
The crossing frequency is selected to 90Hz or 120Hz with a slope of 24dB/oct.
The frequency choice depends to the sound reproduction desire.
It is advisable to use the 120Hz crossover frequency with up to four DVA T4
speakers and the 90Hz crossover frequency with more than four DVA T4 speakers
9)
"SUB PHASE " SWITCH
This switch permits 180° rotation of the audio signal reproduced by subwoofer.
Rotation makes for easier optimization of low-frequency reproduction even in the
most difficult installation situations. After completing installation, reproduce a piece
of music and adjust the switch to obtain the best low-frequency sound.
10)
"ON" INDICATOR LIGHT
The "ON" indicator light comes on green to indicate the amplifier is switched on and it
is working properly.
11)
"SIGNAL -20dB " INDICATOR LIGHT
This indicator comes on green to indicate the presence of the audio signal (at a level
of -20dB).
12)
"PEAK" INDICATOR LIGHT
This indicator comes on red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
It is lights for a few seconds during the switching on.
13)
"INPUT SENS" INPUT SENSITIVITY CONTROL
This control regulates the sensitivity of the signal at amplifier input.
This control does not affect the "LINK" and "BALANCED X-OVER OUTPUT" output
levels
14)
"SDD - SUBWOOFER DIGITAL DELAY" TIME DELAY OPTIONAL
The DVA S20 speaker is available with a circuit called SDD - SUBWOOFER DIGITAL
DELAY.
This circuit permits delaying the audio signal produced by the subwoofer to optimise
alignment together DVA T4 speaker.
7
TECHNICAL SPECIFICATION
System
Type of amplifier
RMS power
Musical power
Frequency responce +/-3dB
Crossover
Sound pressure (SPL)
Component parts
Input sensitivity nominal
Impedance input
Balanced
Unbalanced
Power supply
Speaker shape
Dimension [LxHxP]
Weight
7
14
4
6
BALANCED
S
D
D
X-OVER
OUTPUT
PUSH
SUBWOOFER DIGITAL DELAY
OPTIONAL CARD
1
2
B
3
d
TECHNOLOGIES
MAINS INPUT
MAINS FUSE
POWER
ON
OFF
3
2
1
Active
Digital - Classe T
2000 W (1000W + 1000W)
4000 W
25-150Hz
90 - 120Hz
24dB/oct
138 peak
2 woofer 18" - coil100mm - neodymium
0 dBu
20Kohm
10Kohm
see label on the amplifier
rectangular
1100x720x580mm
74Kg
5
8
9
10
11
12
13
B
d
TECHNOLOGIES
TECHNOLOGIES
S S
2 2 0 0
Digital Vertical Array
BALANCED
LINK
MAIN INPUT
PUSH
120Hz
0°
ON
PEAK
+10dB
90Hz
180°
+4dB
0dB
1 = GND
1
2
2
1
2 = HOT
3
3
3 = COLD
SUB
SUB
SIGNAL
INPUT
X-OVER
PHASE
-20dB
SENS
WARNING
HOT SURFACE
SERIAL N.
"AVIS"
"CAUTION"
RISQUE DE CHOC ELECTRIQUE
TO PREVENT ELECTRICAL SHOCK
NE PAS OUVRIR
DO NOT REMOVE COVER
POUR PREVENIR TOUT RISQUE DE FEU
TO PREVENT RISK OF FIRE
REPLACER UN FUSIBLE
REPLACE FUSES WITH
DE MÊME CARACTERISTIQUES
SAME TYPE AND RATINGS
CET APPAREIL DOIT ÊNTRE RELIÉ A LA TERRE
THIS APPARATUS MUST BE EARTHED
4
8
Werbung
Inhaltsverzeichnis
