Controls And Functions; Technical Specifications - dB Technologies SUB 15D Bedienungsanleitung

CONTROLS AND FUNCTIONS
1) " BALANCED INPUT 1"
Balanced inputs at line level.
2) " OUT 1 " AND " OUT 2 " OUTPUT CONNECT
The "XLR" connectors be used to send the input audio signal to another amplified
speaker .
The signal is choosing between "LINK/XOVER" (10) switch.
3) "LIMITER" INDICA TOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has trip
This prevent s amplifier distortion and protect
4) "SIGNAL" INDICA TOR LIGHT
This indicator shows green to indicate the presence of the audio signal
20dB).
5) "MUTE" INDICA TOR LIGHT
This yellow indicator indicates amplifier status.
The LED is of f in normal operating conditions.
6) "READY" INDICA TOR LIGHT
This indicator shows green to indicate that the main power voltage is correct.
The LED shows green normal operating conditions
7) "INPUT SENS" INPUT SENSITIVITY
This control adjusts the sensitivity of the signal amplifier input.
This control does not af
8) "PHASE" SWITCH
This two-position switch permit
subwoofer by 180°.
Rot ation makes it easier to optimise the reproduction of the low frequencies even in
the most dif ficult inst allation situations.
music and move the switch to achieve the best sound reproduction at low
frequencies.
9) "XOVER" SWITCH
T h i s s w i t c h p e r m i ts s e l e c t i n g t h e c r o s s o v e r f r e q u e n c y b e t w e e n t h e
subwoofer and the speakers connected to the "OUT 1 " and "OUT 2 " outputs.
Choice depends on the type of speaker used for reproduction of mid-high
frequencies.
For speakers with 12" cones, it is best to use 120Hz, while with 15"
speakers 90Hz.
10) "LINK/XOVER" SWITCH
This switch allows to select the signal type to send "OUT 1 " and "OUT 2 " outputs.
The "LINK" position allows to link the same input signal.
The "XOVER" position allows to send input signal according to crossover frequency
select by XOVER (9) switch.
11) "MAINS INPUT" POWER SOCKET
For connecting the power cable provided.
The connector used for mains connection is a POWER CON® (blue) socket
12) "MAINS OUTPUT LINK" POWER SOCKET
For linking the mains power. The output is connected in parallel with input (11) and
can be used to power another active speaker.
The connector is a POWER CON® (grey) socket
13) "MAINS FUSE" FUSE CARRIER
Mains fuse housing.
11
AND " BALANCED INPUT 2"INPUT CONNECT
Accept "XLR" sockets.
ORS
s the speakers against overloads.
CONTROL
fect the " OUT 1 " and " OUT 2 " output s levels
s turning the audio signal reproduced by the
After completing installation, play a piece of

TECHNICAL SPECIFICATIONS

ORS
System
Type of amplifier
RMS power
Frequency response
Crossover
ped.
Sound pressure
Components
(at a level of -
Input sensitivity
Impedance input
Power supply
Housing shape
Colour
Dimension (WxHxD)
Weight
Pole mount cup
Handle
SUB 15D
Active
Class D
800W
40-120Hz (-3dB)
90Hz - 120Hz selectable
24dB/oct
(max SPL) 133dB
1x15" woofer - 3" voice coil
max -3dBu
Balanced 20Kohm
Unbalanced 10Kohm
Internally selectable
100-120Vac 50-60Hz
220-2400Vac 50-60Hz
Rectangular
Black
436x600x600mm
32Kg
M20 (aluminium)
2 (1x per side)
SUB 18D
Active
Class D
1000W
35-120Hz (-3dB)
90Hz - 120Hz selectable
24dB/oct
134dB
1x18" woofer - 4" voice coil
max -3dBu
Balanced 20Kohm
Unbalanced 10Kohm
Full-range con PFC
100-240Vac 50-60Hz
Rectangular
Black
530x700x600mm
44Kg
2 x M20 (aluminium)
4 (2x per side)
12