Operating Instructions; Technical Data - Truma Ultraheat Gebrauchsanweisung

Operating
instructions
Always observe the oper-
ating instructions and
„Important operating
notes" prior to starting!
The vehicle owner is respon-
sible for correct operation of
the appliance.
Control panel
with thermostat
Ultraheat
c
b
2000
a
b
500
b
1000
230 V ~
a = Rotary switch „Off"
b = Rotary switch „On"
power settings:
500 – 1000 – 2000 W
c = Rotary control knob for
room temperature (illumi-
nated by green indicator
lamp „operation")
Switching on
Before switching on,
ensure that the fuse
protection for the power sup-
ply of the camp site is suffi-
cient for the selected power
setting (b – see Technical
Data).
Important: The electric feed
line for the caravan must be
fully unwound from the cable
drum.
1. To switch on, turn the ro-
tary switch to the desired
output level (b).
2. Set rotary control knob (c)
to the desired room tempera-
ture.
The thermostat setting on the
control panel (1 – 9) must be
determined individually de-
pending on the heating re-
quirement and the type of
vehicle.
For an average room temper-
ature of about 23°C, we rec-
ommend a thermostat setting
of about 6 – 8.
Switching off
Switch the heating system
off at the rotary switch (a).

Technical Data

Power supply:
230 V ~, 50 Hz
Power consumption at
power setting
500 W: 2.2 A
1000 W: 4.5 A
2000 W: 8.5 A
Weight: approx. 2 kg
Declaration of conformity:
The Truma-Ultraheat has
been tested by the DVGW
(German Association of Gas
and Water Experts) as an ad-
ditional electric heating unit
and complies with EC Stan-
dard 90/396 for gas appli-
ances, EC EMC standard
89/336, EC 73/23 low voltage
standard as well as other ap-
plicable EC standards and is
authorized to bear the CE
sign.
The CE Product Identity
Number of the heating sys-
tem remains valid without
change.
Accessories
1. Extension cable for the
control panel, length 5-me-
tres (Art. no. 34300-01)
– not illustrated –
2. Remote sensor FFC 2,
monitors the room tempera-
ture, regardless to the posi-
tion of the control panel,
comes with a 4 m connecting
cable (Art. no. 34201-01).
Manufacturer's
terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions in
the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
– for parts subject to wear
and in cases of natural
wear and tear,
– as a result of not original
Truma parts being used in
the appliance and as a re-
sult of unsuitable gas pres-
sure regulators being used,
– as a consequence of failure
to respect Truma instruc-
tions for installation and
use,
– as a consequence of
improper handling,
– as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion
of the purchase agreement
between the seller and the
final consumer. The manufac-
turers will make good such
defects by subsequent fulfil-
ment, i.e. at their discretion
either by repair or replace-
ment. In the event of manu-
facturers providing service
under warranty, the term of
the warranty shall not re-
commence anew with regard
to the repaired or replaced
parts; rather, the old warranty
period shall continue to run.
More extensive claims, in
particular claims for compen-
satory damages by pur-
chasers or third parties, shall
be excluded. This does not
affect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty – in particular
transportation costs, travel-
ling expenses, job and mater-
ial costs, as long as the
service is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and in-
stallation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is: Truma Gerätetechnik
GmbH & Co. KG, Wernher-
von-Braun Strasse 12,
D-85640 Putzbrunn. In Ger-
many, always notify the
Truma service centre if prob-
lems are encountered; in
other countries the relevant
service partners should be
contacted (see list of ad-
dresses). Any complaints are
to be described in detail. In
addition, the properly com-
pleted guarantee certificate is
to be presented, or the facto-
ry number of the unit and the
date of purchase given.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his own
risk, bring the device to the
manufacturers or send it to
them. If there is damage to
heaters (heat exchangers),
the gas pressure regulator
must also be sent back to the
factory.
In instances of the device be-
ing sent to the works, dis-
patch is to be effected by
freight transport. In cases un-
der guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.
5