Installation - Sygonix 420 TVL Bedienungsanleitung

Operating instructions
GB
CCD Colour Camera, 420 TVL, 3.5 - 8 mm
Use in accordance with manufacturer's instructions
This camera is meant for mounting in, and protecting, secluded or critical areas (e.g.
entrance areas, surveillance of underground car parks and the like).
The product is only intended for use in dry, closed interiors, it must not get damp or
wet.
The camera may only be operated via the mains voltage (230 V/AC, 50 Hz).
Please bear in mind that it is prohibited by law to observe strangers with a camera with-
out their knowledge and consent. Observe the rules and regulations of the country
where you are using the camera.
Any use other than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
The safety instructions must be observed at all times!
This product complies with the applicable national and European requirements.
All names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• CCD colour camera with DC lens
• Lens adapter ring, connection plug for control bush
• Operating Instructions
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The arrow symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury
caused by improper use or failure to observe the safety instructions. In
such cases the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is inad-
missible because of safety and approval reasons (CE). Never dismantle the
product.
• The product is not a toy and must be kept out of the reach of children. It
should be operated out of the reach of children. There is the risk of a fatal
electric shock!
• The product may only be operated on the mains voltage (see section "Tech-
nical Data"). Never try to operate the product at another voltage as this will
cause its destruction.
• The product is designed in protection class I. Connect it to a mains socket
with protective earth conductor.
• The camera is only intended for use in dry, closed interiors, it must not get
damp or wet. Never touch the mains plug when your hands are wet or damp!
Danger of a lethal electric shock!
• The camera should not be exposed to extreme temperatures, direct sun-
light, strong vibrations or heavy mechanical stress.
• The use of this camera does not replace the personal supervision of children
or people who require special assistance, but only serves as a support to
this supervision.
The home technology brand for the entire house. More information at www.sygonix.com
• Make sure that the mains cable is not pinched or damaged by sharp edges.
If the mains cable or the camera is damaged, deenergise the mains socket to
which the camera is connected (switch off at the corresponding circuit break-
er or remove fuse). Then, remove the mains plug from the mains socket. Do
not use the product anymore but bring it to a specialized workshop.
• Do not carelessly leave the packaging material lying around since it could be-
come a dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or ac-
cidental drops, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating in-
structions and safety notices for these devices must be followed as well.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
- the device was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Materials are to be observed.
• Ensure that all the electrical connections and connection cables between
the different devices and any extension cables comply with the regulations
and comply with the operating instructions.
• Disconnect the power supply from the power socket if the camera will not
be used for a while (e.g. storage).
• If you have any questions that are not answered in this manual, please
contact our technical service or another specialist.
Connection and Control Elements
7
1
4
5
2
3 6
8
1 Rotary knob for the adjustment of the lens iris (for auto iris lens with DC control).
2 VIDEO/DC switch (preset to "DC")
3 DIP switch for function selection
4 BNC video output
5 Power LED (is switched on during power supply)
6 Mains cable with mit mains plug featuring a protective ground contact
7 Fastening screw for focal length adjustment
8 Fastening screw for focus adjustment
9 Connector for control bush
10 Tripod socket for the fastening on the camera's top and bottom.

Installation

This product is only to be installed and used indoors in dry conditions.
By means of the tripod socket (10) on the top and bottom, the camera can be mounted
to a wall or ceiling using a suitable bracket (not included in the delivery).
Pay attention when tightening the bracket that no cables or pipes are damaged.
The camera should not be pointed directly at bright sources of light or the sun, since
the image will be overdriven by this. Avoid vibrations, dust and magnetic/electric fi elds
at the mounting location. Do not bend the connection cable.
9 10
10