Low Battery Indicator; Storage And Cleaning - Braun ExactFit 3 BP 6000 Anleitung

Erasing data
M
Press and hold memory button (2) for more than 5 seconds,
LCD will blink display "dEL ALL"(if the "slide switch is in User A
side, the user A icon will show ") or "dEL ALL"(if slide switch is in
User B side, the user B icon will show).
M
Press memory button (2) again, LCD will display "---" to mean
all the stored data of corresponding user have been deleted.
Irregular heart beat detector (for BP6200 only)
The appearance of this symbol signifies that a certain pulse irregularity was detected during the
measurement. Talking, moving, shaking or an irregular pulse during the measurement can result in the
appearance of this icon. Usually this is not a cause for concern, however if the symbol appears often,
we recommend you seek medical advice. The device does not replace a cardiac examination, but serve
to detect pulse irregularities at an early stage.

Low battery indicator

When the low battery indicator flashes on the display, it means the battery is low and the four
batteries need to be replaced with alkaline LR6 (AA) batteries.
**
After replacing batteries, BPM will go into time-setting mode automatically and show the
last measurement time on screen. Please set the current date / time before taking the next
measurement to get correct average result.

Storage and cleaning

• Always keep the unit in the carrying case after its use.
• Do not put the item directly under the sunlight, in high temperature or humid and dusty places.
• Do not store in extremely low (less than -20°C) or high (more than 60°C) temperature.
• Use a piece of cloth with water or mild cleansing agent to clean the case and then use a piece of dry
cloth to wipe it dry. Use a piece of dry cloth to wipe the cuff when it is dirty.
• Do not use any strong cleansers to clean it.
• When the unit is not to be used for a long time, remove the batteries.
(Batteries may leak or cause harm).
Calibration
This device was designed and manufactured for a long service life, however it is generally
recommended to have the device inspected once a year to ensure correct function and accuracy.
Please contact the authorised service centre located in your country. Note: The calibration checking
is not a free service. Please contact the Authorized Service Centre to get a quotation before you send
out the product.
This device is not intended as a substitute for regular check-ups by your doctor, please continue to
visit your doctor on a regular basis for a professional reading.
Production date is given by the LOT located in the back of the device. The first 3 numeric digits
after the LOT No represents the day of the year of manufacture. The next 2 numeric digits represent
the last two numbers of the calendar year of manufacture and the letters at the end designate the
manufacturer of the product. E.g. LOT 15612VAL this product was made on the day 156, year 2012 at
manufacturer identifier VAL.
10
A
D M
P
A A
What to do if .....
Problem Reason
Heart rate Appears in the measurement
symbol condition and flashes when
pulse is detected.
Low battery Appears when the battery
indicator voltage is excessively low or the
positions of the batteries are
incorrect.
Measuring Appears when the accurate
error blood pressure and pulse could
not be obtained.
E1 shows The cuff is not secure
E2 shows The cuff is very tight
E3 shows Over-pressure
E4 shows The monitor detected motion
while measuring
Eexx shows Measure incorrectly
Solution
• Measurement in progress, remain quiet.
• Replace all four batteries with new ones.
Insert the batteries in the correct
positions. Be aware of +/- positions.
• Press "start/stop" button again and
remeasure.
• Check if cuff is wrapped according
to instructions.
• Check that there are no kinks in tube.
• Check palm if exerting effort.
• Check if talking or moving
during measurement.
• Check if posture is correct.
• Refasten the cuff and then measure again.
• Refasten the cuff and then measure again.
• Relax for a moment and then measure again.
• Movement can affect the measurement.
Relax for a moment and then measure again.
• Relax for a moment and then measure again.
• Retake the measurement. If the problem
persists, contact the retailer or our customer
service department for further assistance.
Refer to the warranty for contact information
and return instructions.
11