Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Connection and Start-up
1
1
2
2
3
• Fix the ground spikes (2) to the lower ends of the three LED lights (1) and screw them tight.
• Connect the plugs (3) of the LED lights serially to the corresponding connectors on the special
connection cable (4) provided and observe the correct direction.
Screw the cap nut tight, but do not apply too much force! Do not over tighten the cap nuts!
If the cap nut are not tightened sufficiently, water can enter and corrosion may damage the
plugs.
• Connect the mains plug (5) on the special connection cable (4) to the connector on the trans-
former (6); tighten the cap nut as for the 3 lights.
• Place the lights in appropriate locations. Pay attention when placing the earth spikes that no
power, gas or water pipes are damaged!
Carefully push the spikes into the earth (grass, flower bed, etc.) Do not apply any force or use
any tools (e.g. a hammer) since this could damage the product; Warranty/guarantee void!
Lay the cables in such a way no one can trip over them and so that the cables cannot be
mechanically damaged (e.g. sharp edges, stones and the like).
The cables must not be driven over by vehicles; further do not step on the cables.
Do not place the transformer in or under water or at locations where standing water
collects or could be expected to collect (e.g floods, puddles).
The connection cables and the LED lights are not suitable for underwater use.
Never direct water from a garden hose, or from any other irrigation system, at the
product!
• The transformer (6) can be fixed in place using the 4 mounting holes and appropriate screws.
Do not damage the transformer so in doing; do not screw into the transformer; dan-
ger to life from electric shock!
• When all connections have been made, the mains plug (7) can be plugged in to a mains sock-
et (230~/50Hz).
Now the LEDs in the lights should illuminate.
Taking Out of Service
• Unplug the mains plug from the mains socket. If the product is to be stored, clean all the com-
ponents first; see next chapter.
• Store it in a dry and well-ventilated place. Keep the product out of the reach of children.
1
2
3
3
4
Maintenance and Care
The product is maintenance-free. Never dismantle the product (except to perform the tasks
described in this operating manual). Repair or maintenance work must be carried out by a spe-
cialist!
Check the product regularly for damage or leakage. If you have a reason to believe that the
device can no longer be operated safely, disconnect it immediately and secure it against being
operated unintentionally.
It can be assumed that safe operation is no longer possible if:
- the device shows visible signs of damage
- the device no longer operates
- the device was stored under unfavourable conditions for a long period of time or
- the device was exposed to extraordinary stress caused by transport.
7
The LED lights used have a long lifetime; they do not need to be and cannot be exchanged.
Only clean the product with a soft, clean, dry cloth. If it is very dirty, use a cloth slightly moistened
with lukewarm tap water.
Never use aggressive cleaning agents or chemical solutions as the surface of the housing could
be damaged (discoloured).
Do not apply too much pressure to the surfaces, otherwise the stainless steel or the transparent
plastic of the lights may be scratched.
6
Before using the product again, dry the mains cable and the mains plug thorough-
ly - danger to life from electric shock!
5
Disposal
Please dispose of the device when it is no longer of use, according to the current
statutory requirements.
Technical Data
Operating voltage: ......................230 V~/50Hz
Light source: ................................12 white LEDs per lamp
Protection type: ............................IP44 (Transformer: IP64)
Protection class: ..........................II
© Copyright 2008 by Conrad Electronic SE.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in tech-
nology and equipment reserved.
Werbung
Inhaltsverzeichnis
