Maintenance / Service - Skil 2320 Originalbetriebsanleitung

EXPLANATION OF SYMBOLS ON TOOL/CHARGER
3 Read the instruction manual before use
4 Only use the charger indoors
5 Double insulation (no earth wire required)
6 Do not dispose of the charger together with household
waste material
7 Do not dispose of the battery together with household
waste material
USE
• Charging battery 2
- connect charger A with both wall socket and contact B
- indicator C starts blinking GREEN indicating that the
battery is being charged
- after 3 hours the battery is fully charged and charging
automatically stops (green light stays on after blinking)
- if the tool is used only briefly, the charging time can be
very short
- unplug the charger when the battery is fully charged
IMPORTANT:
- if indicator C starts blinking RED, this may mean that
the battery is too cold or too hot; when the battery
temperature returns to between 0°C and 45°C, the
charger will automatically begin charging
- the lithium-ion battery can be charged at any time
(interrupting the charging procedure does not damage
the battery)
- while charging, tool and charger may become warm to
touch; this is normal and does not indicate a problem
Battery protection
•
Switches off the tool or reduces the speed automatically
when
- the load is too high
- the battery is empty
! do not continue to press the on/off switch after
the tool is switched off automatically; battery may
be damaged
• On/Off 8
• Speed control for smooth starting 9
• Changing direction of rotation q
- indicator F shows the selected direction of rotation
- when not properly set in left/right position, switch D 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits w
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! only use sharp bits
• Torque control (VariTorque) e
- output torque will increase as clutch ring H is rotated
from 1 to 17; position J will lock up the clutch to permit
drilling or driving heavy duty work
- when turning in a screw, first try VariTorque position 1
and increase until the desired depth has been reached
• Mechanical gear selection r (2330)
- set selector K to desired speed
! actuate the gear selector while tool is running
slowly
LOW
- low speed
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
HIGH
- high speed
- lower torque
- for drilling small diameters
• Battery level indicator C t
- indicates the charge condition of the battery for a few
seconds when switch D 2 is pressed half or fully
through
- consists of a two-colour LED
- continuous lighting, green : 33-100%
- continuous lighting, red : 11-33%
- flashing light, red : < 11%
Spot light y
•
Spot light L automatically lights on when activating
switch D 2
• Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) u
- keep ventilation slots M 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• For more tips see www.skil.com

MAINTENANCE / SERVICE

This tool is not intended for professional use
•
• Keep tool and charger clean
! unplug charger from power source before
cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send both charger and
tool to your dealer or the SKIL service station
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
8