Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
Pocket Scale PS-H200
Item-No. 12 42 60
Intended Use
The pocket scale is intended to be used for accurately weighing objects up to a total weight of
200 grams. The minimum load is 0.4 grams. A tare and adjustment function are built in.
The scale is only designed for short, direct weighing. Dynamic weighing (e.g. pouring material)
is not feasible and will result in erroneous measurements.
The pocket scale is powered by batteries. Power is supplied via two Lithium coin cells, which
are included in the delivery.
Do not operate the scale where there is a risk of explosions. Do not use the scale for humans
or animals, for medical purposes, or in commercial trade for determining prices.
Any other use than described above is not permitted, it could cause damage to the product and
personal injury. No part of the product may be modified or rebuilt!
The safety instructions are to be observed without fail!
Safety Instructions
Please read all of the operating instructions before using the product for the
first time; they contain important information about the correct operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases.
This device left the manufacture's factory in a safe and perfect condition.
We kindly request the user to observe the safety instructions and warnings contained in the
enclosed operating instructions so this condition is maintained and to ensure safe operation.
Please pay attention to the following symbols:
A triangle containing an exclamation mark indicates important information in these
operating instructions which is to be observed without fail.
This product has been CE tested and complies with the required European guide-
lines.
The „hand" symbol is used to indicate where specific hints and information on han-
dling are given.
The unauthorized conversion and/or modification of the product is inadmissible for reasons of
safety and approval (CE).
Avoid strong mechanical stresses, such as impacts, vibrations or drops.
Avoid strong electromagnetic fields (e.g. large motors, etc.), draughts or thermal fluctuations,
as well as humidity. These may lead to measurement variations and erroneous measurements.
Keep the unit out of the reach of children. It is not a toy.
Do not leave packaging materials unattended. They could become a dangerous playthings for
children.
On industrial sites, the accident prevention regulations of the association of the industrial work-
ers' society for electrical equipment and utilities must be followed.
Never switch the device on immediately after it has been taken from a cold into a warm envi-
ronment. Condensation that forms might destroy your device. Allow the device to reach room
temperature before switching it on.
You should also heed the safety instructions in each chapter of these instructions.
Package Contents
Pocket scale
2 Lithium coin cells (type CR2032)
Weighing plate made from high-grade steel
Artificial leather case
Operating Instructions
Description of the Parts
1 TARE-button for taring and adjusting
2 MODE button to select the weight unit
®
3 ON-OFF button, to switch on and off
4 Display
°
5 Weighing plate with stainless steel support
6 Battery compartment on the rear
Version 01/11
7 Flap lid
Start-up
The maximum weighing range of 200 g must not
be exceeded. Avoid thermal fluctuations during weighing; this may lead to
erroneous measurements.
Inserting/Replacing the Batteries
The pocket scale is powered by batteries. When using for the first time, the plastic strip must be
removed from the battery compartment. Open the cover of the battery compartment and
remove the plastic strip from the battery compartment.
If the symbol „Lo" appears in the measuring mode, and the scale then turns off, new batteries
need to be inserted.
To insert and replace the batteries, proceed as follows:
Close the flap lid (7) and remove the battery compartment lid on
the rear. Slide the cover sideways, off the device.
Pry the two batteries on the side openings out of the support, using
a sharp tool.
Insert two new Lithium coin cells of the type CR2032 in the compart-
ment, paying attention to the correct polarity. The positive pole of
both coin cells is to point outwards. Slide the coin cells diagonally into
the housing, and press them carefully into the fixture until the plastic
clip locks the battery. Take note of the polarity information in the bat-
tery compartment.
Close the battery compartment carefully.
Do not mix old and new batteries. Always replace all the
batteries at the same time, otherwise the batteries discharge each other. Always use
batteries of the same type and brand.
Do not leave flat batteries in the appliance. Even batteries protected against
leaking can corrode and thus release chemicals that could be detrimental to
your health or damage the appliance.
Remove the batteries, if the appliance is not to be used for long while, to pre-
vent leaking.
Leaking or damaged batteries might cause severe burns if the come into con-
tact with the skin. Therefore, use suitable protective gloves.
Do not leave batteries lying around carelessly. They might be swallowed by
children or pets. If swallowed, consult a doctor immediately.
Make sure that the batteries are not short-circuited. Do not throw batteries into
a fire.
Batteries (non-rechargeable) must not be recharged. There is danger of explo-
sion.
You can order suitable Lithium coin cells stating the following order number:
Order No. 65 20 27 (please order 2).
Weighing
Preparation
Place the pocket scale on a stable, level surface and open the flap lid.
Press the „ON/OFF" button (3), to switch on the scale. After a short check and zero-setting
phase (Display „ZEro"), the scale is ready for use. Avoid vibrations and loading of the the weigh-
ing plate during this phase. When the check has been completed successfully, a circle appears,
in the lower left corner (-> o <-) indicating stable measuring conditions, as well as the reading
„0.00" or „0.000".
If the display „out" is shown after a short while, the automatic zeroing has failed. Remove any
weights that might be placed on the weighing plate and make sure it is on an even surface. Turn
the device off and then on again.
Press the „ON/OFF" button to turn off. „OFF" will appear on the display and the device will
turn off.
When the measuring range is exceeded, „- - - - -" is shown. In this case, imme-
diately remove the item to be weighed from the pocket scale, as it may be dam-
aged otherwise.
7
6
5
4
88888
. .
.
g
oz
T
dwt
o
o
ozt
ON
MODE
TARE
OFF
3
2
1
Werbung
Inhaltsverzeichnis
