5
To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination
angle and retighten the fixation screws.
6
After installation, the device requires inspections periodically to prevent the possibility of rot, deformation
and looseness.
CONNECTIONS
Projector 3
Starting address 21
SAFETY ROPE
LED STP-10 Sunbar 3200K 10x5W Light Bar 6°
LED
No. 42103491 EAN 4026397626780
100-240V AC, 50/60 Hz ~
60 W T1A,250V
MIC
0.2m
STP-10
T =45°C
T =55°C
a
C
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
Sunbar
97297 Waldbuttelbrunn Germany www.steinigke.de
POWER IN
MENU
UP
DOWN
ENTER
100-240 V 50/60 Hz ~
T 1 A, 250 V
SENSITIVITY
DMX512 control
A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR
connectors for DMX connection.
1
Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
2
Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always
connect one output to the input of the next unit until all units are connected.
3
At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between
Signal (–) and Signal (+) in the DMX output of the last unit.
4
If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended
to insert a DMX level amplifier to ensure proper data transmission.
5
XLR connection:
Connection to the mains
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.
1
Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on.
2
To switch off the unit, disconnect the power plug.
3
Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains
outlet which is switchable.
Power supply of further devices
The jack POWER OUT allows for power supply of further devices. To interconnect several devices, connect
the jack POWER OUT to the input POWER IN of the next unit until all units are connected. Matching power
cables with P-Con plugs are available as accessories. In this manner, up to 8 devices can be linked at
230/240 input voltage and up to 4 devices at 110/115 input voltage.
Starting address 11
DMX OUT
DMX IN
SAFETY ROPE
LED STP-10 Sunbar 3200K 10x5W Light Bar 6°
LED
No. 42103491 EAN 4026397626780
100-240V AC, 50/60 Hz ~
STP-10
T =45°C
T =55°C
a
C
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
1: Ground
Sunbar
97297 Waldbuttelbrunn Germany www.steinigke.de
2: Signal (-)
POWER IN
POWER OUT
3: Signal (+)
100-240 V 50/60 Hz ~
T 1 A, 250 V
120 Ohms
Projector 2
DMX OUT
DMX IN
60 W T1A,250V
MIC
0.2m
1: Ground
MENU
2: Signal (-)
UP
DOWN
ENTER
POWER OUT
SENSITIVITY
3: Signal (+)
20/28
Projector 1
Starting address 1
SAFETY ROPE
LED STP-10 Sunbar 3200K 10x5W Light Bar 6°
LED
No. 42103491 EAN 4026397626780
100-240V AC, 50/60 Hz ~
60 W T1A,250V
MIC
0.2m
STP-10
T =45°C
T =55°C
a
C
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
Sunbar
97297 Waldbuttelbrunn Germany www.steinigke.de
POWER IN
MENU
UP
DOWN
ENTER
100-240 V 50/60 Hz ~
T 1 A, 250 V
SENSITIVITY
DMX-512 Controller
00114401.DOCX, Version 1.1
DMX OUT
DMX IN
1: Ground
2: Signal (-)
POWER OUT
3: Signal (+)