Answer Alarm Call; Remote Control; System Dialing Function; Alarming Record Checking - mt vision AS-200 Bedienungsanleitung

Operation Instructions

7. Answer Alarm Call

When the main unit sounds alarm, it will dial the preset numbers. If no one answers
the call, the system will call the next user number automatically. The system will call
each preset numbers for 3 times in order.
If you answer the call, you will hear the pre-record voice. You can set system via your
telephone or mobile phone keypad.
If you hang-up directly without answering the call, the system will call each preset
number for 3 times circularly.
Press *: Read the alarm information.
Press 1: Main unit stops alarming and Arm; it stops calling users.
Press 2: Main unit stops alarming and Disarm; it stops calling users.
Press 3: Siren off and monitors the scene for 60 seconds; for continued monitoring,
press 3 again to monitor for another 60 seconds.
Press 4: Main unit starts a 60-second two-way intercom. It cannot be controlled by
the mobile during the time of intercom.
Press 5: Linkage switch 1, 12V output on.
Press 6: Linkage switch 1, 12V output off.
For the above operation of "arm, disarm and output control", you could also send
SMS to realize. The SMS content format is: operation password (default: 1234) +
[1/2/5/6].

8. Remote control

Dial the number associated to the alarm main unit by phone (mobile phone), and
after one ringing cycle, you can hear a voice prompt "Please enter password". If the
password is right, you will here "Press 1 to arm, Press 2 to disarm, Press 3 to Moni-
tor, Press 4 to Intercom".
If the password is wrong, you will hear a prompt voice "wrong password, please
re-enter".
Press 1: arm, if finished successfully, you will hear a voice prompt "System armed".
Press 2: disarm, if finished successfully, you will hear a voice prompt "System di-
sarmed".
Press 3: monitoring for 60 seconds, to continue monitoring, press 3 again to monitor
for another 60 seconds.
Press 4: two-way intercom for 60 seconds. You can't operate the main unit during
this time.
Press 5: Linkage switch 1, 12V output on
Press 6: Linkage switch 1, 12V output off
ENGLISH
22
Operation Instructions
Note:
For each number pressing, it is valid only you hear a "DI" confirmation sound.
Please reenter it if you do not hear the sound. And sometimes for weak gsm
signal, you need to input for several times.

9. System Dialing Function

In disarm status; you can use the main unit to make any call just like a land-line
telephone. Dial telephone number on keypad, press CALL button, the main unit will
make a beep and the [Signal] indicator will be flashing. After the call, press CALL
button again, the main unit will be in disarm status.

10. Alarming Record Checking

In disarm state, input *0 #, then the main unit will make a long beep and enters the
state of alarm record checking. After displaying the alarm and defense zone number
indicator for 1 second, the LCD screen will display the exact alarming time of this de-
fense zone. Press 2, you can upturn to check the previous alarming record; press 8,
downturn to check; and press *# to exit checking.
For example: the 51st defense zone; the 7th alarming; alarming time: 12:10, August
1st, 2008. LCD display for one second,
and then display
the alarming time:
You can also check the alarm records by SMS (Max: Latest 9 records). SMS Check
Command: Remote Control Password (Default: 1234) + [3] Reply SMS:
Eg: Alarm record:
NO1 Zone: 05 TIME: 11-06-25 11:37
(It indicates the first record: wireless zone 5 alarm time)
NO9 Zone: 19 Time: 11-06-25 11:45
(It indicates the ninth record: wireless zone 19 alarm time)
ENGLISH
23