Before Starting The Equipment - EINHELL LK 70 Originalbetriebsanleitung

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Information
•
Remove all adhesive retention tapes, if there
are any, before putting the equipment into
operation. The water container may hold ac-
cessories.
•
Please note that the minimum distance bet-
ween the equipment and the wall to the side
and rear must be 40cm. The minimum dis-
tance to other objects at the front must be 1m.
•
The device must never be tilted, moved or
emptied while switched on or while connec-
ted to the power supply.
•
Only ever move the device when the water
tank is empty and the device has been dis-
connected from the power supply.
•
Use only clean, cold tap water or distilled
water.
•
Never add any scents or fragrances to the
water.
•
The settings which have been made are
shown on the LED display. The applicable
LEDs shine.
5.2 Filling with water (Fig. 3)
•
Pull the water container (9) out as far as it
will go.
•
Fill up the water container (9).
•
To improve the cooling effect you can place
normal ice cubes and/or the frozen cooling
elements (Fig. 2 / Item C), after you have filled
the elements with water before freezing, in
the water container. Please watch out for the
water level if you do this.
•
Push the water container (9) back into the
housing.
Make sure that the water level lies between
the „min" and „max" marks.
•
Replace the water once a week.
6. Operation (Fig. 4)
Insert the power plug into a live socket outlet. A
short signal will sound.
Anleitung_LK_70_SPK7.indb 18 Anleitung_LK_70_SPK7.indb 18
GB
6.1 Switching the equipment on/off (Item 20)
Press the Power button to switch on the equip-
ment. Air will then be blown out at medium, uni-
form fan speed. Press the button again to switch
off the equipment.
6.2 Switching on the vertical slat adjustment
(Item 21)
Press the „Wind" button for the vertical slats to
swing automatically back and forth. Press the but-
ton again to switch off this function.
6.3 Switching on fan mode (Item 22)
The fan is set to „Normal" as standard. Press the
„MODE" button to change the setting in the fol-
lowing order: Normal – Natural – Sleep. The LEDs
will light up accordingly.
Normal: Uniform fan speed
Natural: Non-uniform fan speed
Sleep: The fan speed slows down in accordance
with a timed sequence (30 min. fast –> 30 min.
medium –> permanently slow).
6.4 Switching on the timer (Item 23)
Press the „TIMER" button to limit the ON time to
0.5 – 7.5 hours. One press of the button equals
0.5 hours; the LEDs for 0.5h – 4h will light up ac-
cording to the set time.
6.5 Setting the fan speed (Item 24)
Press the „SPEED" button to set the fan speed in
the following order: Medium – Fast – Slow – Me-
dium. The LEDs „MI – HI – LO –MI" will light up
accordingly.
6.6 Switching on cooling mode (Item 25)
Note: Make sure that the water level in the wa-
ter container lies between the „min" and „max"
marks. Otherwise cooling mode will not work and
the „COOL" LED will blink (see 5.2). A warning
signal will sound.
Press the „COOL" button. The „COOL" LED will
light up. The integrated pump will convey the (ice-
cooled) water up and out of the container so that
it then fl ows down over the honeycomb insert. The
air which is suctioned in will be blown out cooler
and with a higher air humidity than when it was
suctioned in. The cooler the water in the water
tank, the cooler the air which is blown out.
- 18 -
27.02.2017 10:50:05 27.02.2017 10:50:05