Advice On Disposal; Troubleshooting - Bosch TDS14 Serie Gebrauchsanleitung

en
Cleaning & Maintenance
Important:
Always unplug the appliance from the mains supply before
carrying out any cleaning or maintenance operation on it.
1. After ironing, pull out the plug and allow the appliance to cool down
before cleaning.
2. Wipe the housing, handle and iron body with a damp cloth.
3. If the soleplate is soiled with dirt or scale, clean it with a damp cloth.
4. Never use abrasive products or solvents.
Storing the appliance (D)
1. Set the main power to the "0" position and disconnect the mains
cable.
2. Always allow the appliance to cool down before storing it.
3. Place the iron on the iron pad, standing on the soleplate.
4. Empty the boiler and store the mains cable and the steam hose in
the storage compartment. Do not wrap the cords too tight.
Fabric protection soleplate cover (E)
(depending on the model)
The fabric-protection soleplate cover is used for steam-ironing delicate
garments at maximum temperature without damaging them. Use of
the soleplate cover also does away with the need for a cloth to prevent
shine on dark materials.
It is advisable to first iron a small section on the inside of the garment
to see if it is suitable.
Trouble shooting
Problem
The steam generator does
not come on.
The iron does not heat up.
The iron begins to smoke
when switched on.
Water flows through the holes
on the sole plate.
Dirt comes out through the
sole plate.
The iron does not produce
any steam.
The ironed garment turns
dark and/or sticks to the
soleplate.
The soleplate turns brown.
Loss of pressure during
ironing.
If the above does not solve the problem, get in touch with authorized technical service.

Possible causes
• There is a connection problem.
• The main power button is not switched on.
• The main power button is not switched on.
• The temperature control knob is set to the "min"
position.
• During first use: Certain components on the
appliance have been lightly greased at the factory
and may produce a little smoke when initially
heated.
• During later use: the soleplate may be soiled.
• The steam function is being used before it has
reached temperature.
• The water is condensing inside the pipes because
steam is being used for the first time or has not
been used for a long time.
• There is a build-up of scale or minerals in the boiler.
• Chemical products or additives have been used.
• The boiler is not switched on or is empty.
• The steam regulator is set to the minimum position.
• The selected temperature is too high and has
damaged the garment.
• This is a regular consequence of usage.
Steam release button activated during a long period
of time.
To attach the soleplate cover to the iron, place the tip of the iron into
the end of the soleplate cover and pull the elastic strap over the lower
rear of the iron until it fits tightly. To release the soleplate cover, pull the
elastic strap and remove the iron.
The fabric-protection soleplate cover may be purchased from the
customer service or specialist shops:
Accessory code
(After-sales)
464851
464849*
* Cork handle iron

Advice on disposal

Our goods come in optimised packaging. This basically consists in
using non-contaminating materials which should be handed over to
the local waste disposal service as secondary raw materials. Your local
town council can give you information about how to dispose of obsolete
appliances.
This appliance is labelled in accordance with European
Directive 2002/96/EG concerning used electrical and
electronic appliances (waste electrical and electronic
equipment - WEEE).
The guideline determines the framework for the return and
recycling of used appliances as applicable throughout the EU.
You can download this manual from the local homepages of
Bosch.
• Check the mains cable, the plug and the socket.
• Switch the main power button (8) to the on
position.("I")
• Switch the main power button (8) to the on
position.("I")
• Set the temperature control knob (11) to the desired
position.
• This is completely normal and will stop after a short
while.
• Clean the soleplate according to the cleaning
instructions in this manual.
• Reduce the steam flow when ironing at low
temperatures (Variable steam control (9)).
• Point the iron away from the ironing area and
press the steam release button (12) until steam is
produced.
• Clean the boiler
Use tap water mixed 50% with distilled or
demineralised water. If the tap water in your district
is very hard, mix tap water with distilled water 1:2.
• Clean the sole plate with a damp cloth.
• Never add products to the boiler
• Switch the main power button (8) to the on
position.("I") and/or fill the boiler
• Increase the steam flow by turning the steam control
(9).
• Select a suitable temperature for the material and
clean the sole plate with a damp cloth.
• Clean the soleplate regularly with a damp cloth.
Use the steam release button (12) with intervals. This
improves the ironing result as the textiles will be dried
and stay smooth better.
Name of accessory
(Specialist outlets)
TDZ1510
TDZ1520*
Solution