Inhaltsverzeichnis
Werbung
CHAPTER 13
FAULT
CAUSE
1. Does not function
Mains plug not plugged in
on any programme
Mains switch not on
No power
Electric circuit fuses failure
Load door open
2. Does not load
See cause 1
water
Inlet tap turned off
Timer not set correctly
3. Does not discharge
Discharge tube bent
water
Odd material blocking filter
4. Water on floor around
Leak from the washer between the tap
washing machine
and inlet tube
5. Does not spin
The washing machine has not
discharged water
"No spin" setting (some models only)
The presence of excessive foam has
aborted the spinning phase
6. Strong vibrations
Washing machine not perfectly level
during spin
Transport bracket not removed
Washing load not evenly distributed
7. Display reads error
–
0, 1, 5, 7, 8, 9
8. Display reads
No water fill.
error 2
9. Display reads
No pump out.
error 3
10. Display reads
Machine overfilled with water.
error 4
NOTE:
THE INITIAL SPIN AT THE BEGINNING OF THE WASHING CYCLE IS A NORMAL PHASE OF THE
PROGRAM AND NOT A MACHINE FAULT.
If the fault should persist, contact a Candy Technical Assistance Centre. For prompt servicing, give the model of
the washing machine, to be found on the label placed on the cabinet inside of the porthole or on the
guarantee certificate.
Important
1 The use of environment friendly detersives without phosphates may produce the following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not
compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not
remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing machine detersives are often
difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the
formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Candy
Technical Assistance Service.
78
EN
REMEDY
Insert plug
Turn on mains switch
Check
Check
Close load door
Check
Turn on water inlet tap
Set timer on correct position
Straighten discharge tube
Check filter
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Turn the programme dial onto spin setting
Do not use excessive amounts of
detergent
Adjust special feet
Remove transport bracket
Distribute the washing evenly
Call service.
Check water supplies are on.
Check drain is clear.
Check drain hose is not kinked.
Turn off water supply to machine.
Call service.
Le constructeur décline toute responsabilité pour les éventuelles erreurs d'imprimerie
contenues dans le présent mode d'emploi. Il se réserve en outre le droit d'apporter
toutes modifications qui se révèleraient utiles à ses propes produits sans pour autant
en compromettre les caractéristiques essentielles.
La Ditta costruttrice declina ogni responsabilità per eventuali errori di stampa contenuti
nel presente libretto. Si riserva inoltre il diritto di apportare le modifiche che si
renderanno utili ai propri prodotti senza compromettere le caratteristiche essenziali.
Wir schileßen die Haftung für alle evtl. Druckfehler aus. Kleinere Änderungen und
technische Weiterentwicklungen im Detail vorbehalten.
V˘robce se omlouvá za pfiípadné tiskové chyby v tomto návodû k pouÏití.
Dále si v˘robce vyhrazuje právo provést potfiebné zmûny na sv˘ch v˘robcích,
které nemají vliv na jejich základní charakteristiku.
The manufacturer declines all responsibility in the event of any printing mistakes in
this booklet. The manufacturer also reserves the right to make appropriate
modifications to its products without changing the essential characteristics.
Werbung
Inhaltsverzeichnis
