How To Listen To The Fm Radio; How To Use The Wired Audio Input - Midland BT Next 2.0 Bedienungsanleitung

7. When successfully paired, the Blue light of the unit will be on for one second and
then the unit will exit the setup mode and switch to the working mode (the Blue
light will start flashing).
You can now use your BTNext and the GPS street voice announcement are always
in background.
If you pair the GPS to the Volume + button (because for example the "Volume –"
button was already used), you loose the possibility to pair the phone to the BTNext
unit. You can overcome this limit by pairing the phone directly to the GPS and then
the GPS to the BTNext unit. All the phone features are therefore managed by the
GPS itself.
How to use a GPS
When paired using the "Volume -" button the GPS will be automatically connected
and the voice announcement are always in background also if the intercom is active.
When the GPS is paired to the "Volume +" button, the street voice announcement
will always interrupt the intercom. In addition, remember to switch to "Phone"
mode in order to listen and control the music (play/pause - backward and forward).
If the phone is connected thru the GPS you must use the control buttons on the GPS
screen in order to control the phone functionality.
How to pair PMR446 transceiver with integrated Bluetooth
If your PMR446 trasceiver has an integrated Bluetooth (like the G8BT), you must pair
the trasceiver using the "Volume –" button:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on
permanently.
› Now press firmly (3 sec) the "Volume -" button, the Blue and Red light will flash.
› Follow now the pairing procedure explained on the manual of the transceiver
itself
Attention: If you are pairing to a G8BT transceiver, just when the BTNext finish the
pairing (only the Blu LED is flashing) you must follow this procedure to activate the
Bluetooth connection:
› Turn off and on the G8BT and then press for 3 sec. the "BT" button.
› Follow the same procedure every time you need to reconnect the G8BT to the
BTNext (no need to make the pairing procedure again)

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the
"FM Radio" mode in order to use it. Long press the middle button until you hear "FM
radio" from the voice announcement. Now all the three main button are dedicated
to the FM Radio (See Table C).
Press short the Forward or the Backward button to seek the FM Radio station. When
you press long the Forward or the Backward button, you can scan up or down the 6
recorded stations. A voice announcement will tell you the number of which memory
you are entering. A double beep tone will be played when the last or the first recor-
ded station is reached.
To save the station you are listening, press the Forward and Rear buttons together for
3 sec. You will hear a beep tone for confirmation.
The station is saved over the last recorded station used.
Thanks to the RDS system, the FM Radio will choose the strongest signal available for
the radio station you like to listen.
The RDS system is OFF by default, if needed you can toggle on/off the RDS pressing
together the "Volume +" and "Volume –" buttons for 3 sec when the radio is on. A
voice announcement will tell you the RDS status.
FM Radio with intercom
When you are in "FM Radio" mode is not possible to manually open the intercom,
you can only open it using VOX feature (just talk) to the unit paired on the "Middle"
button. To manually activate the intercom you must switch to "Intercom" mode.

How to use the wired audio input

Your Midland BTNext is also supplied with a wired audio input (AUX), that can be
used to connect an audio source, like an iPod (or any other MP3 Player) or a PMR446
transceiver for group communication or for a coverage increase.
Listening to music
To listen to music from the wired input, connect the audio source using the cable
supplied with the BTNext unit. The volume level can be adjusted using the Voume +
and Volume – button, or automatically adjusted by the AGC system, which means
that you only need to adjust the volume of your iPod/ MP3 player to a level that will
allow you to listen to music in normal speed.
Attention: never set the volume of the MP3 Player to the maximum possible. Normally
the best level is about the 70% of the maximum.
Hint: We recommend that you perform a few tests adjusting the volume of your
iPod/MP3 player so at the normal speed the Headset volume is suited to your needs.
The AGC system will automatically increase the volume on higher speed. Make a
note to remember this setting for future trips.
Midland BT Next - 25