Bosch GCM Professional 80SJ Originalbetriebsanleitung Seite 23

OBJ_BUCH-2154-004.book Page 23 Wednesday, June 14, 2017 5:06 PM
19 Retracting blade guard
20 Roller
21 Fence
22 Saw table
23 Insert plate
24 Mitre angle indicator
25 Locking knob for various mitre angles
26 Mitre detent lever
27 Tilt protector
28 Detents for standard mitre angles
29 Spindle lock
30 Transport safety-lock
31 Scale for bevel angle
32 Indicator for bevel angle
33 Stop screw for 0° bevel angle
34 Stop for 0° bevel angle
35 Hex key (size 5 mm)/cross-head screwdriver
36 Hex socket screw for mounting of saw blade
37 Clamping flange
38 Interior clamping flange
39 Saw blade
40 Locking screw of the adjustable fence
41 Mounting holes for material clamp
42 Threaded rod
43 Screws for insert plate
44 Screw for bevel angle indicator
45 Screw for mitre angle indicator
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
3 601 M19 ...
Rated power input
No-load speed min
Reduced starting current
Weight according to EPTA-
Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 26.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Bosch Power Tools
Noise Information
Sound emission values determined according to
EN 62841-3-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
The noise emission value given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It may also
be used for a preliminary estimation of noise emissions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used for
other applications, with different accessories or is poorly
maintained, the noise emission value may differ. This may sig-
nificantly increase noise emissions over the total working pe-
riod.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually being
used, should also be taken into account. This may significant-
ly reduce noise emissions over the total working period.
Assembly
 Avoid unintentional starting of the machine. During as-
Delivery Scope
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Material clamp 7
– Saw-table extension 3
GCM 80 SJ
– Hex key/cross-head screwdriver 35
GCM 800 SJ
Note: Check the power tool for possible damage.
GCM 8000 SJ
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
... 0.. ... 06.
All parts must be properly mounted and all conditions fulfilled
W 1400 1250
that ensure faultless operation.
-1
5500 5500
Damaged protective devices and parts must be immediately
 
replaced by an authorised service centre.
Mounting Saw-table Extensions (see figure A)
kg 14.1 14.1
The saw table can be extended left and right with the saw-ta-
/II /II
ble extensions 3.
– Slide the saw table extensions in as far as they will go
– Turn the power tool upside down so that you can screw in
mm 216
mm 1.3–1.8
mm 3.3
mm 30
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Clamping screw 2 x 2, cross-head screw x 2 to prevent the
saw table extensions from being pulled out of the saw table
through the holes provided in the saw table.
the two cross-head screws provided to prevent the saw ta-
ble extensions from being pulled out of the saw table.
Screw the cross-head screws into the threaded holes pro-
vided in the saw table extensions 3 and use a cross-head
screwdriver 35 to tighten them.
English | 23
1 609 92A 3BW | (14.6.17)