Dell Broadcom NetXtreme II Benutzerhandbuch Seite 105

iSCSI-Protokoll: Broadcom NetXtreme-II®Netzwerkadapter Benutzerhandbuch
29 Fehler
30 Fehler
31 Fehler
32 Informationen
33 Fehler
34 Informationen
35 Fehler
36 Fehler
37 Fehler
38 Fehler
39 Fehler
40 Fehler
41 Fehler
42 Fehler
43 Fehler
44 Fehler
45 Fehler
46 Fehler
47 Fehler
48 Fehler
49 Fehler
50 Fehler
51 Fehler
52 Fehler
53 Fehler
54 Fehler
55 Fehler
56 Fehler
57 Fehler
58 Fehler
59 Fehler
60 Fehler
61 Fehler
62 Fehler
63 Fehler
64 Informationen Attempt to bootstrap Windows using iSCSI NIC Boot (iBF).
file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/German/iscsi.htm[9/5/2014 3:49:06 PM]
Target rejected an iSCSI PDU sent by the initiator. Dump data contains the rejected
PDU.
Initiator could not allocate a work item for processing a request.
Initiator could not allocate resource for processing a request.
Initiator received an asynchronous logout message. The Target name is given in the
dump data.
Challenge size given by the target exceeds the maximum specified in iSCSI
specification.
A connection to the target was lost, but Initiator successfully reconnected to the target.
Dump data contains the target name.
Target CHAP secret is smaller than the minimum size (12 bytes) required by the
specification.
Initiator CHAP secret is smaller than the minimum size (12 bytes) required by the
specification. Dump data contains the given CHAP secret.
FIPS service could not be initialized. Persistent logons will not be processed.
Initiator requires CHAP for logon authentication, but target did not offer CHAP.
Initiator sent a task management command to reset the target. The target name is
given in the dump data.
Target requires logon authentication via CHAP, but Initiator is not configured to perform
CHAP.
Target did not send AuthMethod key during security negotiation phase.
Target sent an invalid status sequence number for a connection. Dump data contains
Expected Status Sequence number followed by the given status sequence number.
Target failed to respond in time for a login request.
Target failed to respond in time for a logout request.
Target failed to respond in time for a login request. This login request was for adding a
new connection to a session.
Target failed to respond in time for a SendTargets command.
Target failed to respond in time for a SCSI command sent through a WMI request.
Target failed to respond in time to a NOP request.
Target failed to respond in time to a Task Management request.
Target failed to respond in time to a Text Command sent to renegotiate iSCSI
parameters.
Target failed to respond in time to a logout request sent in response to an
asynchronous message from the target.
Initiator Service failed to respond in time to a request to configure IPSec resources for
an iSCSI connection.
Initiator Service failed to respond in time to a request to release IPSec resources
allocated for an iSCSI connection.
Initiator Service failed to respond in time to a request to encrypt or decrypt data.
Initiator failed to allocate resources to send data to target.
Initiator could not map an user virtual address to kernel virtual address resulting in I/O
failure.
Initiator could not allocate required resources for processing a request resulting in I/O
failure.
Initiator could not allocate a tag for processing a request resulting in I/O failure.
Target dropped the connection before the initiator could transition to Full Feature Phase.
Target sent data in SCSI Response PDU instead of Data_IN PDU. Only Sense Data can
be sent in SCSI Response.
Target set DataPduInOrder to NO when initiator requested YES. Login will be failed.
Target set DataSequenceInOrder to NO when initiator requested YES. Login will be
failed.
Cannot reset the target or LUN. Will attempt session recovery.