Specifications - Makita LS1216 Betriebsanleitung

ENGLISH
(Original instructions)
1 Stopper pin
2 Hex bolts
3 Blade guard
4 Kerf board
5 Saw blade
6 Blade teeth
7 Left bevel cut
8 Straight cut
9 Right bevel cut
10 Lock lever
11 Locking screw
12 Adjusting bolt
13 Turn base
14 Stopper lever
15 Slide pipe
16 Top surface of turn base
17 Periphery of blade
18 Guide fence
19 Adjusting screw
20 Stopper arm
21 Grip
22 Cam
23 Lever
24 Latch lever
25 Scale plate
26 Release button
27 Pointer
28 Lock-off button
29 Switch trigger
30 Hole for padlock
31 Switch for light
32 Light
33 Switch for laser
34 Socket wrench
35 Wrench holder
36 Center cover

SPECIFICATIONS

Model
Blade diameter .................................................................................................................................................... 305 mm
Hole diameter .....................................................European countries: 30 mm, other than European countries: 25.4 mm
Max. Miter angle .................................................................................................................................. Left 52°, Right 60°
Max. Bevel angle ................................................................................................................................. Left and Right 45°
Max. cutting capacities (H x W)
Miter angle
Thickness of wood
0°
facing on guide
fence for increased
height of cut
45° (left and
Thickness of wood
right)
facing on guide
fence for increased
height of cut
Explanation of general view
37 Shaft lock
38 Blade case
39 Arrow
40 Outer flange
41 Inner flange
42 Spindle
43 Ring
44 Dust nozzle
45 Dust bag
46 Fastener
47 Dust box
48 Cover
49 Button
50 Cylinder section
51 Sawdust
52 Support
53 Turn base
54 Clamping screws
55 Upper fence
56 Lower fence
57 Red indicating area
58 Vise knob
59 Vise arm
60 Vise rod
61 Screw
62 Vise plate
63 Vise nut
64 Holder
65 52/38° type crown molding
66 45° type crown molding
67 45° type cove molding
68 Inside corner
69 Outside corner
70 Crown molding stopper L
(Optional accessory)
45° (left)
59 mm × 382 mm
69 mm × 363 mm
35 mm 78 mm × 290 mm
60 mm –
59 mm × 268 mm
69 mm × 255 mm
30 mm –
45 mm –
71 Crown molding stopper R
(Optional accessory)
72 Crown molding stopper L
73 Crown molding stopper R
74 Crown molding
75 Vise
76 Spacer block
77 Aluminum extrusion
78 Over 15 mm
79 Over 290 mm
80 Over 340 mm
81 Hole
82 Cut grooves with blade
83 Screws (two each side)
84 Lower fence
85 Base
86 Platform
87 Triangular rule
88 Miter scale
89 Bevel scale plate
90 0° Angle adjusting bolt
91 Scale plate
92 Left 45° bevel angle adjusting
bolt
93 Right 45° bevel angle adjusting
bolt
94 Workpiece
95 Laser line
96 Vertical vise
97 Screwdriver
98 Screw (one piece only)
99 Lens for the laser light
100 Limit mark
101 Brush holder cap
LS1216/LS1216L/LS1216F/LS1216FL
Bevel angle
0°
87 mm × 382 mm 44 mm × 382 mm
102 mm × 363 mm 54 mm × 363 mm
115 mm × 300 mm 61 mm × 290 mm
120 mm × 250 mm
87 mm × 268 mm 44 mm × 268 mm
102 mm × 255 mm 54 mm × 255 mm
115 mm × 202 mm
120 mm × 172 mm
45° (right)
–
–
–
15