Denon ADV-700 Bedienungsanleitung Seite 24

ENGLISH
(3) AUTO DECODE mode
• In the auto decode mode, it is possible to play signals in the Dolby Digital, Dolby Pro Logic II or DTS, according to the format of
the input signals.
• It is also possible to play 2-channel sources according to the 2-channel decode mode and Dolby Pro Logic II mode settings (page
23) and in the Dolby Pro Logic II Surround mode.
[1] Dolby Digital and DTS playback (digital inputs only)
• Applicable sources
• Digital inputs (TV/DBS and V.AUX functions, including DVD
playback discs)
Dolby Digital multi-channel sources
DTS sources
3
c 8 1:02:46
1
DVD
TONE
1,3
CH
ON 1 2 3
POWER POWER VCR
CH
OFF 4 5 6
VCR POWER VCR POWER CH
VOL
CLEAR 7 8 9
TV
TV POWER TV POWER CH TV/VCR SLEEP
+10 0
CALL
DISPLAY RETURN INPUT MODE SURROUND
3
2
MENU FUNCTION
1
6 6
ENTER
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
RDS PTY CT RT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
5
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
1
Select the digital input function. (DVD or TV/DBS or
V.AUX digital input)
FUNCTION
FUNCTION
/SELECT
Main unit Remote control unit
2
Set the input mode to
INPUT MODE
"AUTO".
DTS sources can also be
played in the input mode
"DTS".
Remote control unit
24
3
Set the surround mode to "AUTO DECODE".
SURROUND FUNCTION
SURROUND
MODE
/SELECT
\
Main unit Main unit Remote control unit
When performing this operation from the main unit,
press the SURROUND MODE button then turn the
FUNCTION/SELECT dial to choose the surround
mode.
4
Play a program source containing the
mark.
• The Dolby Digital indicator
DIGITAL
lights when playing a
Dolby Digital source.
• The DTS indicator lights
DTS Lit
when playing a DTS
source.
The mode is selected automatically according to the
format of the source being played.
5
Display the surround parameters
SURR.PARA
for the source.
The surround parameters are
also displayed on the screen
when the function is set to
Remote control unit
DVD.
6
Select the various surround
parameters and set them.
The display returns to
normal if no operation is
performed for 4 seconds
while the parameters are
Remote control unit
displayed.
• D.COMP. setting
D.COMP. OFF
OFF LOW MID HI
, /
This parameter is not displayed when playing DTS
source.
6
• LFE level setting
LFE 0dB
... ...
-10 -5
, /
The LFE level can be adjusted between –10 dB and
0 dB in steps of 1 dB.
• DEFAULT setting
DEFAULT Y N
YES NO
, /
or
When "YES" is selected, the settings are reset to
their factory default values.
Lit
Stop operating buttons once the surround parameter
settings have been completed.
seconds the normal display reappears and the
settings are automatically set.
NOTES:
• When "DEFAULT" is selected and the
is pressed ("YES"), "D.COMP." is automatically set to
"OFF" and "LFE" is reset to the default value.
("D.COMP." is not valid for DTS source.)
• Signals encoded in Dolby Digital can only be played in
the Auto decode (Dolby Digital, Dolby Pro Logic II or
Auto stereo), Direct, stereo or virtual modes. Other
modes do not work when playing Dolby Digital signals.
• DTS signals can only be played in the Auto decode
(DTS), Direct or stereo modes. Other modes do not
work when playing DTS signals.
• DTS signals can also be played in the "DTS" input
mode. (See page 19.) In this case, decoding and
playback are only performed when DTS signals are
input.
Surround parameters (3)
D.COMP. (Dynamic Range Compression):
• Motion picture soundtracks have tremendous
dynamic range (the contrast between very soft and
0 very loud sounds). For listening late at night, or
whenever the maximum sound level is lower than
usual, the Dynamic Range Compression allows you to
hear all of the sounds in the soundtrack (but with
reduced dynamic range). (This only works when
playing program sources recorded in Dolby Digital.)
Select one of the four parameters ("OFF", "LOW",
"MID" (middle) or "HI" (high)). Set to OFF for normal
listening.
LFE (Low Frequency Effect):
• Program source and adjustment range
1. Dolby Digital: –10 dB to 0 dB
2. DTS Surround: –10 dB to 0 dB
• When Dolby Digital encoded software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
correct Dolby Digital playback.
• When DTS encoded movie software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
correct DTS playback.
• When DTS encoded music software is played, it is
recommended that the LFE LEVEL be set to –10 dB
for correct DTS playback.
After several
cursor button