Components List - sportplus SP-HT-9800-iE Bedienungsanleitung

4. COMPONENTS LIST

No. Description Quantity
1 Computer
2 Upper computer cable
3 Bolt
4L Computer plastic cover L
4R Computer plastic cover R
5 Bolt
6 Bolt
7 Saddle
8 Tube spacer
9 T-shaped round head grooved pin
10R Seat post plastic cover L
10L Seat post plastic cover R
11 Bolt
12 Seat post set
13 Tube bundle
14 Round head grooved pin
15 Tension cable
16 Lower computer cable
17 Sensor set
18 Sensor
19 Flywheel frame
20 Ball bearings
21 Washer
22 Waved washer
23 Safety ring
24 Round head grooved pin
25 Slide tube
26 Nut
27 Tube end cap
Housing
28L
L
Housing
28R
R
29 Bolt
30L Pedal crank L
30R Pedal crank R
31 Anti-loose hex head bolt
32 Crank end cap
33L Pedal L
33R Pedal R
34 Bolt
35 Joint lever
36 Hex screw
37 Spring washer
38 Washer
39 Axle for flywheel holder
40 Nut
41 Hex screw
42 Tapered spring
SP-HT-9800-iE-IM-DE+GB+FR-04.indb 30-31
No. Description Quantity
1 43 Magnet set
1 44 Washer
4 45 Washer
1 46 Rear end cap
1 47 Rear Stabilizer
8 48 Flat washer
2 49 Allen head screw
1 50 Power cable
1 51 Spring washer
1 52 Washer
1 53 Belt wheel
1 54 Belt
2 55 Pedal Axle
1 56 Allen head screw
1 57 Upper protective cover
1 58L Front end cap L
1 58R Front end cap R
1 59 Front Stabilizer
1 60 Motor
1 61 Allen head screw
1 62 Waved washer
30 63 Handlebar post
1
64 Pulse contact surfaces
1
65 Bolt
1
66 Foam handle
1
67 Hand pulse cable
1
68 End cap
2
69 Handlebar
1
70 Nut
1 71 Idler
72 Waved washer
1
73 Idler rack
6
74 Spring
1
75 Spring
1
76 Ball bearings
2
77 Washer
2
78 Flywheel
1
79 One-way ball bearing
1
80 Ball bearings
8
81 Axle for flywheel
3
82 Small belt wheel
2
83 Bearing
2
84 Nut
2
85 Allen key wrench
1
86 Combination wrench
2
87 Adaptor
1
88 Nut
1
30
5. ASSEMBLY INSTRUCTIONS
Take all parts out of the packaging carefully and place them on a flat surface. When doing this,
use suitable padding to protect the working surface. Assembly of the individual parts should
1
be carried out by 2 people!
1
1
Before assembly, check the parts list to verify that all parts are present. Some parts have already
2
been pre-assembled to simplify the assembly process for you.
1
10
4
1
10
1
1
1
1
STEP 1
3
1
1
4
1
1
7
2
1
2
2
2
2
2
1
2
1
1
1
1
2
1
1
1
1
48
47
1
1
1
1
1. Attach the front stabilizer (59) to the main body. Secure with 2 sets of flat washers (48),
2
spring washers (51) and Allen head screws (49). Tighten securely.
1
1
2. Attach the rear stabilizer (47) to the main body. Secure with 2 sets of flat washers (48),
1
spring washers (51) and Allen head screws (49).
1
Note: You may adjust the rear end cap accordingly to compensate for uneven surfaces.
48
49
51
49
31
59
51
10/6/2016 2:30 PM