Connecting Consumers To The Generator; Overload Cut-Out; Switching Off The Engine; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL 41.523.33 Originalbetriebsanleitung

Anleitung_RT_PG_5500_D_SPK1:_
GB

6.2 Connecting consumers to the generator

Set the selector switch (Fig. 1/Item 5) to the left to
use 230V~ sockets. Important: Even though the
continuous power (S1) of 3000 W is shared in this
position between the 2 sockets, it is also possible
to load only one socket with 3000 W. The total
load of the two sockets may temporarily (S2)
reach a maximum of 3300 W for 5min.
Set the selector switch (Fig. 1/Item 5) to the right
to activate the 400V 3~ socket. Important: This
socket may be loaded continuously (S1) with
3600W and temporarily (S2) for a maximum of
5min. with 5500W.
The generator is suitable for 230 V~ and 400 V 3~
alternating voltage appliances.
Do not connect the generator to the household
mains system as this may result in damage to the
generator itself or to other electrical appliances in
your home.
Note: Some electrical appliances (power jigsaws,
drills, etc.) may have a higher level of power
consumption when used in difficult conditions
Some electrical appliances (for example televisions,
computers, etc.) should not be powered by a
generator. If in doubt, consult the manufacturer of
your appliance.

6.3 Overload cut-out

The generator is fitted with an overload cut-out. This
isolates the relevant sockets if an overload occurs.
Important. If this happens, reduce the electric power
you are taking from the generator or remove any
defective connected appliances.
Important. Defective overload cut-outs must be
replaced only by overload cut-outs of identical design
and with the same performance data. If repairs are
necessary, please contact your customer service
center.
230V~ sockets
If an overload occurs, the 230V~ sockets (Fig. 3/Item
3) will be isolated from the supply. You can restart the
230V~ sockets by pressing the overload switch (Fig.
3/Item 10).
400V 3~ socket
If an overload occurs, the 400V 3~ socket (Fig. 3/Item
8) will be isolated from the supply. You can restart the
400V 3~ sockets by pressing the overload switch
(Fig. 3/Item 9).
16
26.05.2011 7:16 Uhr Seite 16

6.4 Switching off the engine

Before you switch off the generator, allow it to
run briefly with no consumers so that it can "cool
down"
Move the ON/OFF switch (Fig. 1/Item 14) to
position "OFF" with the key.
Close the petrol cock
7. Cleaning, maintenance, storage and
ordering of spare parts
Switch off the motor and pull the spark plug boot
from the spark plug before doing any cleaning and
maintenance work on the equipment.
Important: Switch off the machine immediately
and contact your service station:
In the event of unusual vibrations or noise
If the engine appears to be overloaded or
misfires
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.

7.2 Air filter

In this connection, please also read the service
information.
Clean the air filter at regular intervals, and replace
it if necessary.
Open both clips (Fig. 10/A) and remove the air
filter cover (Fig. 10/B).
Remove the filter elements (Fig. 11/C)
Do not use abrasive cleaning agents or petrol to
clean the elements.
Clean the elements by tapping them on a flat
surface. In cases of stubborn dirt first clean with
soapy water, then rinse with clear water and air-
dry.
Assemble in reverse order