Auto Power Off; Firmware Upgrades - WolfVision VZ-8plus Bedienungsanleitung

Auto Power off

In the "Power control" settings of the on-screen menu you can select that the Visualizer
will be automatically switched off, if it is not used for a certain time.
Changing the standard contrast (color) settings
If the picture or the colors on your screen appear to be too dark, you can lower the
overall contrast of the picture in the "Color settings" menu of the on-screen menu. The
settings can be made separately for the normal mode and the text-mode.
DVI PORT
Pin 1
Pin 9
Pin 17
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (not used)
5 - T.M.D.S. Data4+(not used)
6 - DDC Clock
7 - DDC Data
8 - Analog Vertical Sync
C1 - Analog Red
C4 - Analog Horizontal Sync

Firmware Upgrades

The software (firmware) of your Visualizer (including the o
upgraded to the latest version. First download the latest firmware and WolfVision's firmware
update utility program from Wolfvision's internet homepage at www.wolfvision.com/support.
Then connect the serial port of the Visualizer with the serial port of your computer using a
crossed serial RS232 cable and run the firmware update utility program. More details on
the firmware updates can be found on WolfVision's internet homepage.
Serial control input, RS 232
The serial port can be used to control the Visualizer through an external
device, like a remote control system for a whole conferencing room.
3 4
1 2 5
9-pin D-Sub connector on unit
male, front side
6 7 8 9
Pins: 2: RX, 3: TX, 5: GND, 7: RTS, 8: CTS
Baud rate: 19200 or 9600, databits: 8, stopbit: 1, parity: no
Please note that DecimaI-Codes (=ASCII-Codes or Hex-Codes)
must be sent as one single byte (e.g. 199 and not: 1 + 1 + 9) !
A detailed description of the serial protocol can be found on our
internet homepage:
Pin 8
DVI ports are divided into a digital and an analog
section. Please note that the image of the
External input (#11) is only output at the analog
DVI section!
Pin 24
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (not used)
13 - T.M.D.S. Data3+ (not used)
14 - +5V Power
15 - Ground (return for +5V,
HSync and VSync)
16 - Hot Plug Detect
C2 - Analog Green
C5 - Analog Ground
(analog R, G & B return)
www.wolfvision.com/support
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (not used)
21 - T.M.D.S. Data5+ (not used)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue
n-screen HELP
10
) can easily be
Function: Decimal-Code :
Image on 192
Iris open 193
Focus far 194
Zoom wide 195
Image off 196
Iris close 197
Focus near 198
Zoom tele 199
Preset 1 202
Preset 2 203
Save Preset 1 216
Save Preset 2 217
Preset max. wide 229
Preset A5 231
Preset A6 232
Preset max. tele 235