Bluetooth Function - Pioneer FS-W40 Bedienungsanleitung

> Before Start > Part Names
output level, sampling rate, or frequency response
changed) and the unit does not recognize it as a genuine
DTS signal. In such cases, you may hear noise.
0 Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
Video
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 When the TV image is blurry or unclear, power code or
connection cables of the unit may have interfered. In that
case, keep distance between TV antenna cable and
cables of the unit.
0 Make sure the switching of input screens is proper at the
monitor side such as a TV.
Check the following if the above does not fix the problem:
There is no video
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
There is no picture from a source connected to an HDMI
IN terminal
0 To display video from the connected player on the TV
while the unit is in standby, you need to enable
"Hardware" - "HDMI" - "HDMI Standby Through" in the
System Setup menu. Refer to (
about HDMI Standby Through.
0 Check if "Resolution Error" is displayed on the sound
system controller's display when video input via HDMI IN
jack is not displayed. In this case, the TV does not
support the resolution of the video input from the player.
Change the setting on the player.
0 Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
supported.
52
> Install
Images flicker
0 It is possible that the resolution of the player is not
compatible with the TV's resolution. If you have
connected the player to this unit with an HDMI cable, try
changing the output resolution on the player. There also
may be an improvement if you change the screen mode
on the TV.
Video and audio are out of sync
0 Video may be delayed relative to audio depending on the
settings and connections with your television. To adjust,
press
"Sound Delay" in "AV Adjust".
Linked operation
There is no linked operation with CEC compliant
devices, such as a TV
0 In the System Setup menu of the unit, set "Hardware" -
"HDMI" - "HDMI CEC" to "On".
0 It is also necessary to set HDMI linking on the CEC
compliant device. Check the instruction manual.
0 When connecting a Sharp brand player or recorder by
HDMI, set "Hardware" - "HDMI" - "HDMI Standby
Through" to "Auto" in the System Setup menu.
FM broadcasts
Radio reception is poor or there is a lot of noise.
P18) for information
0 Re-check the antenna connection.
0 Move the antenna away from the power cord.
0 Move the unit away from your TV or PC.
0 Passing cars and airplanes can cause interference.
0 Concrete walls weaken radio signals.
0 Listen to the station in mono.
0 FM reception may become clearer if you use the antenna
jack on the wall used for the TV.
> Setup > Playback
on the remote controller, and adjust in "Other" -
Supplementary information | Firmware Update |

BLUETOOTH function

0 Try plugging/unplugging the power of the unit and try
turning on/off the BLUETOOTH enabled device.
Restarting the BLUETOOTH enabled device may be
effective.
0 The BLUETOOTH enabled devices must support the
A2DP profile.
0 Near components such as microwave oven or cordless
phone, which use the radio wave in the 2.4 GHz range, a
radio wave interference may occur, which disables the
use of this unit.
0 If there is a metallic object near the unit, BLUETOOTH
connection may not be possible as the metal can effect
on the radio waves.
Check the following if the above does not fix the problem:
Cannot connect with this unit
0 Check that the BLUETOOTH function of the
BLUETOOTH enabled device is enabled.
Music playback is unavailable on the unit even after
successful BLUETOOTH connection
0 When the audio volume of your BLUETOOTH enabled
device is set low, the playback of audio may be
unavailable. Turn up the volume on the BLUETOOTH
enabled device.
0 Some BLUETOOTH enabled devices may be equipped
with a Send/Receive selector switch. Select Send mode.
0 Depending on the characteristics or specifications of your
BLUETOOTH enabled device, playback on this unit may
not be possible.
Sound is interrupted
0 There may be a problem with the BLUETOOTH enabled
device. Check the information on the internet.
The audio quality is poor after connection with a
BLUETOOTH enabled device
0 The BLUETOOTH reception is poor. Move the
Others
E
N