Inhaltsverzeichnis
Werbung
① Pull out from here
② Hinge
③ Harness cover
④ Rear view
camera
⑤ Hatch
Fig. 12
Abb. 12
② Waterproof pad
① Clamps
④ Make a U-shaped loop in
the lead outside the rubber
packing to prevent rainwa-
ter from flowing along the
③ Rubber packing
lead into the interior of the
vehicle.
Attach the waterproof pad
using double-sided tape.
Fig. 13
Abb. 13
Connection
<ENGLISH>
Accessory power supply
Note:
• This unit is for vehicles with a 12-volt battery and nega-
To electric terminal controlled by ignition
tive grounding. Before installing it in a recreational vehi-
cle, truck, or bus, check the battery voltage.
switch (12 V DC) ON/OFF.
• To avoid shorts in the electrical system, be sure to discon-
⑥ Red
nect the
battery cable before beginning installation.
⑦ Fuse (1A)
• Refer to the owner's manual for details on connecting the
other units, then make connections correctly.
Ground
• Secure the wiring with cable clamps or adhesive tape. To
protect the wiring, wrap adhesive tape around them where
To vehicle (metal) body.
they lie against metal parts.
⑧ Black
• Route and secure all wiring so it cannot touch any mov-
ing parts, such as the gear shift, handbrake and seat rails.
Cord installation (Fig. 11)
Do not route wiring in places that get hot, such as near
the heater outlet. If the insulation of the wiring melts or
① Clamps
gets torn, there is a danger of the wiring short-circuiting
② Rear view camera
to the vehicle body.
③ RCA power supply cable
• Do not shorten any leads.
• Never feed power to other equipment by cutting the insu-
④ Product with a video input jack
lation of the power supply lead of the unit and tapping
(Hideaway unit etc.)
into the lead. The current capacity of the lead will be
⑤ Power supply unit
exceeded, causing over heating.
⑥ Made with a rasp etc.
• When replacing the fuse, be sure to only use a fuse of the
rating prescribed on the fuse holder.
⑦ Scuff plate
• To minimize noise locate the TV antenna cable, radio
⑧ Clamp
antenna cable and RCA power supply cable as far away
⑨ Waterproof pad
from each other as possible.
• Connection to a TV with an RCA video input is possible,
Attach the waterproof pad using double-
but confirm whether the TV you use has a reverse gear
sided tape.
connection function.
Cord installation points (Fig. 12)
• If this unit is installed in a vehicle that does not have an
ACC (accessory) position on the ignition switch, the red
lead of the unit should be connected to a terminal coupled
• When pulling the cord out of the car,
with ignition switch ON/OFF operations. If this is not
pull from the outer side of the hatch har-
done, the vehicle battery may be drained when you are
away from the vehicle for several hours.
ness cover and hinge.
① Pull out from here
② Hinge
③ Harness cover
④ Rear view camera
⑤ Hatch
After cord installation (Fig. 13)
ACC position
No ACC position
• Open and close the hatch door slowly
to confirm that the cord is not rubbing
• Cords for this product and those for other products may
against the rim of the door.
be different colors even if they have the same function.
• When the rear view camera cord cannot
When connecting this product to another product, refer to
be pulled out from the lower side due to
the supplied manuals of both products and connect cords
that have the same function.
the type of car.
As shown in the figure 13, bend the cord
Connection sample (Fig. 10)
into a U shape in front of the waterproof
pad, making sure that rain water cannot
① Power supply unit
enter the car by running down the cord.
② Rear view camera connector
① Clamps
③ RCA power supply cable connector
② Waterproof pad
④ Rear view camera
③ Rubber packing
④ Make a U-shaped loop in the lead outside
Video input jack
the rubber packing to prevent rainwater from
Connect to camera input jack (REAR
flowing along the lead into the interior of the
VIEW CAMERA IN).
vehicle.
⑤ RCA pin
Attach the waterproof pad using double-
sided tape.
Specifications
<ENGLISH>
Power source ........................................... 14.4 V DC
Dimensions
(10.8 V to 15.1 V allowable)
Camera unit
..... 23 (W) mm × 23 (H) mm × 24 (D) mm
Grounding system .............................. Negative type
........... 7/8 (W) in. × 7/8 (H) in. × 1 (D) in.
Max. current consumption .......................... 100 mA
Output video ....................................... Mirror image
Power supply unit
..... 56 (W) mm × 23 (H) mm × 22 (D) mm
(for rear view confirmation)
..... 2-1/4 (W) in. × 7/8 (H) in. × 7/8 (D) in.
Sensor ......................... 1/4-inch color CMOS sensor
No. of pixels
Weight
.................. effective no. of pixels roughly 310 000
Camera unit ................................ 135 g (0.3 lbs)
Lens ........................................................ Wide-angle,
(including the cable)
focal length f = 1.4 mm, F value 2.3
Power supply unit ...................... 110 g (0.2 lbs)
Angle of view ................... Horizontal: approx. 135º
(including the power cord)
Vertical: approx. 105º
Length
IR cutoff filter (special filter for vehicle mounting)
Rear view camera cable .......... 7 m (23 ft. 4 in.)
.................................................................. Provided
RCA power supply cable ........ 3 m (9 ft. 10 in.)
Iris system .......................................... Electronic iris
Note:
Scanning system ........................................ Interlace
Specifications and the design are subject to possible
Synchronizing system ....... Internal synchronization
modification without prior notice due to improve-
Signal-to-noise ratio .......................... 40 dB or more
ments.
(at the recommended intensity of illumination)
Horizontal resolution ............ Approx. 300 TV lines
Illumination range .... Approx. 0.9 lux to 100 000 lux
Image output .........NTSC compatible 1 Vp-p (75 Ω)
Operation temperature range ........... –30ºC to +70ºC
–22ºF to +158ºF
Storage temperature range .............. –40ºC to +85ºC
–40ºF to +185ºF
Werbung
Inhaltsverzeichnis
