Philips SBCVL1200/86 Bedienungsanleitung Seite 6

Troubleshooting
First, check all cables to ensure that they are connected correctly.
Pr Pr Pr Pr Problem oblem oblem oblem oblem Solution Solution Solution Solution Solution
No picture on TV2 • Ensure that both units are switched on (figure A-5 and B-11 are green).
• Select the EXT. or AV channel on TV2.
• Activate the video source you would like to watch (set-top box: power on; VCR/DVD:
playback).
• Select the correct video source on the Transmitter unit using the input selection
buttons (figure B-14).
• Select the same channel on both the Receiver and Transmitter units (figure A-2, B-8).
Bad quality picture • Move the Receiver unit around, centimetre by centimetre until you get good picture
or sound on TV2
and sound quality.
• Move the Transmitter unit around until you get good picture and sound.
• Put the SCART output mode switch (figure B-1, B-9) of an unused SCART output
connector in the position.
• Put the SCART output mode switch (figure B-1, B-9) of a used SCART output
connector in the position.
• Change both units to another channel (figure A-2, B-8). Select the same channel on
both the Receiver and Transmitter units.
No sound or picture on • Make sure the input selector switch (figure B-14) is in the correct position (pressed
TV2
in).
No picture on TV2
• Ensure that the correct SCART connector of the VCR is being used. (Ext. 1 or Ext. 2.
(VCR is used as a video
Check VCR's user manual).
source)
Initially good picture, • Disable the auto standby mode of the VCR. (Check VCR's user manual).
disappears after several
minutes.
(VCR is used to view a
cable Programme)
Wrong picture on TV2
• Select the EXT. or AV channel on TV2.
• Select another video source on the Transmitter unit using the input selection buttons
(figure B-14).
• Activate the video source you would like to watch (set-top box: power on; VCR/DVD:
playback).
• Swap the SCART connectors on the transmitter unit; they might be mixed up (figure
B-3, B-5).
• You may be picking up a signal from another Wireless TV Link. Switch to another
channel on both Receiver unit and Transmitter unit (figure A-2, B-8) to receive your
own signal. Ensure that the same channel is selected on both units!
No control of Video
• Align the Transmitter unit with the video source(s) you want to control (see figure C).
sources from TV2 • Install the remote control extender cord.
• Ensure that you are using the remote control of the device you want to control.
• Make sure the Transmitter and Receiver units are placed more then 5 metres apart.
• Reposition the remote control extender cord eye on the video source, or place it 5-10
cm in front of the video source.
• Aim the remote control directly at the Receiver unit and ensure that there are no
obstacles in between. (figure A-7 must be flashing)
• Ensure that there is no other wireless device (e.g. headphones) interfering with the
remote control.
• The maximum operating distance between the remote control and the Receiver unit is
7 metres*; be sure you are within this range.
Wrong picture on TV1 • Select the correct EXT. or AV channel on TV1 (see TV instruction manual).
• Select a regular programme number.
8
Pr Problem Pr Pr Pr oblem oblem oblem oblem Solution Solution Solution Solution Solution
Buzzing sound • Move the Receiver unit around, centimetre by centimetre, until the buzzing sound
when using the remote disappears.
control • Move the Transmitter unit around, centimetre by centimetre, until the buzzing sound
disappears.
• In some cases you will not be able to solve this problem.
VCR, DVD, SAT is not • Select the corresponding EXT or AV channel on TV1.
selected on the TV if
switched on
'Easylink' feature • Check that both your TV and VCR support this feature. (Check the TV and VCR's
doesn't work user manuals)
• Use Easylink compatible or fully wired SCART cables.
S-VHS video gives black • Select CVBS video output format for your S-VHS VCR. (Check the VCR's user
& white pictures only on manual)
either TV1 or TV2
DVD player gives no • Select CVBS video output format for your DVD player. (Check the DVD player's user
pictures on either TV 1 manual)
or TV2
* depends on remote control's signal strength and battery condition
Specifications
General
Dimensions: 204 (W) x 168 (D) x 65 (H) mm
Power supply: 220 - 240V AC / 50Hz via power adapters
Operating consumption: 3 W (both transmitter and receiver unit)
Transmitter unit connections: SCART 1 input / output: Stereo Audio / CVBS Video. Supports
'Easylink'
SCART 2 input / output: Stereo Audio / CVBS Video. Supports
'Easylink'
Receiver unit connections: SCART output: Stereo Audio / CVBS Video
Video standards supported: PAL / NTSC / SECAM
Operating range: Up to 100m in open air; up to 30m in house
Number of input devices: 2
Audio / Video transmission
Carrier frequency: 2.4 GHz
Number of channels: 4 (may be less, depending on local regulations)
Type of modulation: FM
Transmission power: <10mW
Antennas: Built-in
Remote Control Extender
Carrier frequency: 433.92 MHz
Type of modulation: AM
Transmission power: <10mW
Range of IR reception: Up to 7 metres max.
Carrier frequency range 32kHz – 40 kHz
Remote control extender cord: Yes, 2 IR eyes
Remote control extender antenna: Antennas at rear of both units
9