WolfVision VZ-C11 Bedienungsanleitung Seite 15

RS-232 / SERIAL PROTOCOL
The serial port can be used to control the Visualizer through an external device, like a remote control
system for a complete conference room.
1 2 3 4 5
6 7 8 9
9-pin D-Sub connector
on unit, male, front side
A detailed description of the serial protocol (including status report and position setting) can be
downloaded from our website: www.wolfvision.com/support.
DVI PORT
Pin 8
Pin 1
Pin 9
Pin 17
Pin 24
EXCHANGING A FUSE
Before changing a fuse disconnect the power cable. The fuse (#27)
is situated behind a small lid above the power socket and the main
power switch. It can easily be opened with a small screwdriver etc..
Please put the new fuse(s) carefully into the socket, and put the socket
the right way round into the socket holder.
The type of fuse is: T 3,15A. Do not use any other type !
Change the fuse for a new one and switch the unit on. If the fuse fails
again contact your Visualizer dealer!
CLEANING
Please note that dust on the base mirror (#1, #2) inside the unit
Mirror:
has little effect on the picture quality (as it is out of the
focal range). Wipe the mirror gently with a soft (!) and lint-free tissue (no paper!).
Normal dry cleaning or cleaning together with breathing a bit on the mirror should
be sufficient (If not, use a special optical cleaner only!)
Please note: To clean the mirrors, the unit has to be opened and needs service trained personnel!
CAUTION: Sensitive front coated mirror!
Move the tissue in vertical direction only ! (Horizontal scratches would
cause ugly reflections) Avoid high pressure !
DO NOT USE ORDINARY GLASS CLEANER OR ALCOHOL
- THE RESULT WOULD BE A SLIGHTLY BLUE MIRROR SURFACE !
The glass covering the mirrors should also be kept clean.
Cabinet: Clean the cabinet by gently wiping it with a soft cloth.
Never use strong cleaning agents such as benzine or alcohol!
Pins: 2: RX, 3: TX, 5: GND, 7: RTS, 8: CTS
Baud rate: 9200, 19200, 38400, 57600 or 115200 (selectable)
databits: 8, stopbit: 1, parity: no
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (*)
5 - T.M.D.S. Data4+(*)
6 - DDC Clock
C1 C2
7 - DDC Data
8 - Analog Vertical Sync
C3 C4
C1 - Analog Red
C5
C4 - Analog Horizontal Sync
C - Analog Ground
(analog R, G & B return)
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (*)
13 - T.M.D.S. Data3+ (*)
14 - +5V Power
15 - Ground (return for +5V,
HSync and Vsync)
16 - Hot Plug Detect
C2 - Analog Green
14
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (*)
21 - T.M.D.S. Data5+ (*)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue
*...not used
IMPORTANT