Herunterladen Diese Seite drucken

Angehängte Maschinen - SIP ORION 120 T Betriebsanleitung

Werbung

18. Die gefahrene Geschwindigkeit muß immer
den
Umgebungsverhältnissen
werden!
Bei
Berg-
Querfahrten
zum
Kurvenfahrten vermeiden!
19. Fahrverhalten, Lenk- und Bremsfähigkeit
werden durch angebaute oder angehängte
Geräte
und
Ballastgewichte
Daher
auf
ausreichende
Bremsfähigkeit achten!
20. Bei
Kurvenfahrt
und/oder die Schwungmasse des Gerätes
berücksichtigen!
21. Geräte nur in Betrieb nehmen, wenn alle
Schutzvorrichtungen angebracht und in
Schutzstellung sind!
22. Der
Aufenthalt
verboten!
23. Nicht im Dreh- und Schwenkbereich des
Gerätes aufhalten!
24. Hydraulische
Klapprahmen
betätigt werden, wenn sich keine Personen
im Schwenkbereich aufhalten!
25. An
fremdkraftbetätigten
hydraulisch) befinden sich Quetsch- und
Scherstellen!
26. Vor dem Verlassen des Traktors Gerät auf
dem Boden absetzen, Motor abstellen und
Zündschlüssel abziehen!
27. Zwischen Traktor und Gerät darf sich
niemand aufhalten, ohne daß das Fahrzeug
gegen Wegrollen durch die Feststellbremse
und/oder durch Unterlegkeile gesichert ist!
Angehängte Maschinen
1.
Das Gerät gegen das Wegrollen sichern.
2.
Maximal zulässige Belastung des Hakens
an der Anbaukupplung, des Zughakens
oder des Anbaubockes berücksichtigen.
3.
Beim Anbau mit der Deichsel muss eine
ausreichende
Anbaupunkt gewehrleistet sein!
angepaßt
und
Talfahrt
und
Hang
plötzliche
beeinflußt.
Lenk-
und
die
weite
Ausladung
im
Arbeitsbereich
dürfen
nur
Teilen
(z.B.
Beweglichkeit
am
18. Always adjust the driving speed to the
driving conditions. Avoid fast turning when
driving uphill, downhill or across the slope!
19. The performance during driving and the
ability of turning is changed, when there are
implements connected or mounted to the
tractor. Pay attention to sufficient ability of
turning and braking!
20. When turning, take into consideration the
load which is outside the centre of gravity
and/or constant weight of the implement!
21. Connect the imlement only when all safety
devices are in position and when the
implement is secured!
22. It is prohibited to be in the working and
dangerous area of the machine!
ist
23. Stay away from the area of swinging and
turning of the machine!
24. Hidraulic flaps, doors etc. may be put in
action only when no one is in the swinging
area!
25. On all parts of the machine, which are
mecanically or hydraulically driven, there is
danger of shear and squeeze!
26. Secure the implement before leaving the
tractor. Lower the implement completely.
Switch off the engine and pull out the
ignition key! Disengage the PTO shaft!
27. Nobody is allowed to be between the tractor
and the implement if the vehicle is not
secured against movement by a brake
or/and by a wedge!
Attached machines
1. Secure the implements against rolling-off.
2. Consider maximal permitted charge on the
hook of attaching coupling, puuling hook or
hitch.
3. If connected by a drawbar, be careful about
the sufficient flexibility in the connecting
point!
51

Werbung

loading

Verwandte Produkte für SIP ORION 120 T

Diese Anleitung auch für:

Orion 50 alp