LGB 65001 Bedienungsanleitung Seite 6

With a Loco Remote or Universal
Remote, press the numbered loco
function buttons. With an MTS Train
Mouse, press the loco function but-
ton the matching number of times.
For example, to turn the sound off or
on, press button "8" on the Loco
Remote or Universal Remote. If you
are using a Train Mouse, press the
function button eight times.
If desired, numerous functions of the
sound decoder, such as acceleration,
braking, direction of travel and many
others, can be programmed using a
PC and the 55045 MTS PC Decoder
Programming Module (see
Instructions for advanced users).
These functions also can be pro-
grammed with the 55015 Universal
Remote.
Sound
This Sound Unit features a digital
electronic sound system. The Sound
Unit features a volume control (Fig.
2).
Most sound features described
below also can be controlled directly
with the LGB Multi-Train System (see
Multi-Train System).
65000 European Steam Sound Unit
This Sound Unit replicates the typical
sounds of a European steam loco-
motive. When a low voltage is on the
tracks, you hear the "whooshing"
sound of the boiler. The whistle
sounds when the loco starts. After
the loco stops, you hear the air pump
and the sound of coal shoveling.
65001 American Steam Sound Unit
This Sound Unit replicates the typical
sounds of an American steam loco-
motive. When a low voltage is on the
tracks, you hear the "whooshing"
sound of the boiler. The whistle
sounds when the loco starts: 2 long
blasts when moving forward, 3 short
12
blasts when reversing. After the loco
stops, you hear the air pump and the
sound of coal shoveling.
Hint: If, with analog operation, the
starting signal sounds for the wrong
direction, swap the wires for the
power supply at the Sound Unit.
65002 European Diesel Sound Unit
This Sound Unit replicates the typical
sounds of a European diesel locomo-
tive. When the throttle is turned up
slowly, you hear starting of the diesel
engine, which then idles. The horn
sounds when the loco starts. After
the loco stops, you hear the idling of
the diesel motor. Then you hear the
motor being turned off.
65003 American Diesel Sound Unit
This Sound Unit replicates the typical
sounds of an American diesel loco-
motive. When the throttle is turned
up slowly, you hear starting of the
diesel engine, which then idles. The
horn sounds when the loco starts: 2
long blasts when moving forward, 3
short blasts when reversing. After
the loco stops, you hear the idling of
the diesel motor. Then you hear the
motor being turned off.
Hint: If, with analog operation, the
starting signal sounds for the wrong
direction, swap the wires for the
power supply at the Sound Unit.
65004 European Electric Loco
Sound Unit
This Sound Unit replicates the typical
sounds of a European electric loco-
motive. When the throttle is turned
up slowly, you hear the main switch
and then the compressor. The main
fan operates when the loco is moving
and when it is standing. The whistle
sounds when the loco starts. After
the loco stops, you hear the vacuum
pump and then the main switch.
Power Supply
Attention! For safety and reliability,
operate this product with LGB power
supplies (transformers, power packs
and controls) only. The use of non-
LGB power supplies will void your
warranty.
Use this product with LGB power
supplies with an output of at least 1
amp. For more information on LGB
power supplies for indoor, outdoor
and multi-train operation, see the
LGB catalog.
INSTRUCTIONS FOR ADVANCED
USERS
MTS Sound Decoder
Programming functions
You can program numerous func-
tions of the sound decoder to suit
your requirements. If you want to do
this, program the "function values"
in "registers" (CVs) using a PC and
the 55045 MTS PC Decoder
Programming Module. You can also
program the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nec-
essary to change the function val-
ues.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister CV55 to function value 55.
This also reprograms the loco
address to the factory pre-set
value.
To reprogram the factory pre-set
function values with the 55015 (dis-
plays shows "P --") input 6, 5, and 5
and press the right arrow button. The
display shows "P --" again: Input 5,
5, and 5 and press the right arrow
button again.
13