Instructions For Cleaning; Troubleshooting - SOLIS Futura 567 Bedienungsanleitung

packing cycle and turn off automatically on its
completion.
– Disconnect the hose from both the Bottle Cap
and the appliance immediately.

INSTRUCTIONS FOR CLEANING

IMPORTANT: Always unplug the appliance
before cleaning the MAGIC VAC ® .
– Carefully wash your hands before proceeding
to clean the appliance and its accessories.
– Both before and after use, clean the exposed
surfaces of the MAGIC VAC using a sponge
®
moistened with a mild, non-abrasive dishwas-
hing detergent. If any liquids accidentally get
inside the appliance, do not connect it to the
mains electricity supply and do not use it;
contact your nearest dealer or authorised
service centre.
– The appliance is provided with a lower part (13)
which is entirely removable and washable also
on the dishwasher top rack (fig. S). Before was-
E
32
– To open a bottle sealed with the MAGIC VAC
Bottle Cap, simply pull the cap out of the bot-
tle. You will hear the air rushing into the bottle.
hing the lower part, remove both gasket (10)
(fig. T) and sealing gasket (11) (fig. U). Clean
both gaskets using a sponge moistened with a
mild washing up liquid and leave them to com-
pletely dry before positioning them again. Once
cleaning and drying are over, carefully fit both
gaskets back in their places. Then reinsert the
lower part (13) in the port provided on the lid
(5).
– Thoroughly wash the MAGIC VAC ® accessories
(containers, caps, jars, etc.) like you would wash
any kitchen utensils, allowing them to
dry completely. If you wash the accessories
in a dishwasher, be sure to place them on
the top rack.

TROUBLESHOOTING

®
The MAGIC VAC does not work
®
– Check the switch (1) position.
– Make sure the MAGIC VAC
in properly. Check the electric socket by plugging
another appliance into it.
– The MAGIC VAC will stop automatically if
®
overheated. Allow it to cool down for 15 minutes
and try again.
– Check for faults in the power cord or the plug.
Should you detect a fault, do not use the
appliance.
The MAGIC VAC fails to apply the first seal
®
on the bag cut from the roll
– Make sure the bag cut from the roll is
properly positioned as described in the para-
graph: „Making bags from MAGIC VAC
rolls"
The MAGIC VAC ® does not create a complete
vacuum in the bags
– To seal the bag properly, you must make sure
that the open end remains completely inside the
Vacuum Chamber.
– Make sure that the Sealing Bar, the Sealing
Gaskets and Airtight Gaskets are free of impuri-
ties. After cleaning them, put them properly
back in place.
– The MAGIC VAC ® bag might have a hole in it.
To check it, seal the bag with air on the inside.
Dip the bag in water and apply pressure. The
appearance of bubbles means that there is a
leak. Reseal or use another bag.
The MAGIC VAC does not seal the bag
®
properly
– If the Sealing Bar overheats and melts the bag,
you may have to raise the Lid and allow the
Sealing Bar to cool down for a few minutes.
– The MAGIC VAC is built in conformity with
®
current safety standards. Overheating will cause
it to turn off automatically. Allow the appliance
to cool down for 15 minutes and try again.
The MAGIC VAC ® bag does not maintain a
vacuum after being sealed
– Leaks along the seam may be caused by creases,
crumbs, grease or liquids. Reopen the bag, clean
the upper inside part of the bag and remove
any foreign material from the Sealing Bar before
resealing it.
– Check that the bag has no holes in it which have
caused air to leak in. Use paper napkins to pro-
has been plugged tect any sharp edges on the contents of the bag.
®
The MAGIC VAC ®
in the containers
– By means of the Connection Hose, connect the
container lid (or the Cap Attachment if neces-
sary) to the Air Inlet of the appliance.
– Leave enough room (at least 3 cm) between the
contents and the top of the jar or container.
– If liquids come out during the vacuum-packing
process, remember that they must first be chilled
in a refrigerator, not left at room temperature.
– Check that the rim of the jar or container and
the universal lid are not damaged in the sealing
® area. Wipe the rim and cap clean with a cloth
moistened with lukewarm water and repeat the
vacuum-packing process.
– Make sure that the gasket of the container cap
or the universal cap is set properly in place and
is not damaged.
MAGIC VAC ® Executive containers or
MAGIC VAC Universal Caps do not maintain
®
a vacuum
– Make sure that the arrow on the knob of the
container cap is positioned on „VACUUM"
before creating a vacuum in the container and
it is positioned on „CLOSED" after a vacuum
is formed.
– Make sure that the O-ring beneath the knob
of the container cap or the universal cap is set
properly in place.
MAGIC VAC ® Family containers do not
maintain a vacuum
– Make sure that the gasket beneath the central
button (17) of the container cap is set properly
in place and is not damaged.
does not create a vacuum
E
33