Yamaha CVP-89 Bedienungsanleitung Seite 72

i
Assembly/Zusammenbau/Montage/Montaje
1
2
Blanket, etc.
Decke o.ä.
Couverture, etc.
Manta, etc.
4
1
Four 5 x 20mm screws
Vier 5 x 20 mm Schrauben
1
Quatre vis de 5 x 20 mm
Cuatro tornillos de 5 x 20 mm
Five 4 x 20 mm round-head screws
Fünf 4 x 20 mm Rundkopfschrauben
Cinq vis à tête ronde de 4 x 20 mm
Cinco tornillos de cabeza redonda de 4 x 20 mm
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5 x 20 mm screws
5 x 20 mm Schrauben
Vis de 5 x 20 mm
Tornillos de 5 x 20 mm
4 x 20 mm round-head screws
4 x 20 mm Rundkopfschrauben
2
x5
Vis à tête ronde de 4 x 20 mm
Tornillos de cabeza redonda de
4 x 20 mm
3
Six 5 x 20 mm screws
Sechs 5 x 20 mm Schrauben
Six vis de 5 x 20 mm
Seis tornillos de 5 x 20 mm
Black
Schwarz
Noir
Negro
1
1
2
2
2
2
1
x18
1
1
1
1
White
Weiß
Blanc
Blanco
Black
Schwarz
Noir
Negro
1
Two 5 x 20 mm screws
1
Zwei 5 x 20 mm Schrauben
1
Deux vis de 5 x 20 mm
1
Dos tornillos de 5 x 20 mm
Assembly
NOTES
• We do not recommend attempting to as-
semble the Clavinova alone. The job can be
easily accomplished, however, with only
two people.
• Use only the screws provided or replace-
ments of exactly the specified size. Using
screws of the wrong size can result in dam-
age to the instrument.
Z
Open the box and remove all
the parts.
On opening the box you should find
the parts shown in the illustration above.
Check to make sure that all the required
parts are provided.
X
Carefully lean the main unit
against a wall.
To make it easier to install the legs,
place a soft blanket or similar material
on the floor near a wall, close the
Clavinova keyboard cover, place the
front panel of the Clavinova (the side
with the keyboard) on the blanket and
gently lean the unit against the wall —
MAKING SURE THAT IT CAN NOT
FALL — as shown in the illustration.
C
Attach the front legs.
Securely attach the two front legs
using six 5 x 20 mm screws 1 each (use
a Philips "+" screwdriver), as shown in
the illustration. Make sure the screws are
securely tightened.
V
Attach the rear leg and pedal
box assembly.
Before attaching the rear leg and
pedal box assembly, insert the 3 plugs
extending from the rear leg into the cor-
responding sockets in the main unit,
making sure that the connectors must be
inserted with the protruding clip facing
the rear of the main unit. Then securely
attach the rear leg with the six 5 x 20
mm screws 1, and the pedal bracket
with the five 4 x 20 mm round-head
screws 2.
IMPORTANT
• After assembling the Clavinova, check once
more to make sure that all screws have
been securely fastened.
• If the stand leans to the side, makes unu-
sual noises, or otherwise seems unstable
during use, check and tighten all screws
while following the assembly instructions
given above.