Identification Of The Parts; Mounting; Cable Adjustment - Texas 4650 TR/WE Bedienungsanleitung

Only use orginal spare parts or accessories. If
not orginal parts or accessories is used, the
liablility is no longer applied.
Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the
handle-mounted clutch cable, must not be
removed or exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are
explosive.
Ensure that the machine is properly secured
when transported on a flatbed etc.
Waste electrical products must not be
disposed of with the household waste. This
tool should be taken to your local recycling
centre for safe treatment.
The lawnmower is manufactured according to the latest
safety requirements. These include a blade brake that
stops the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your lawnmower.

Identification of the parts

See Illustration 2
Notice: the illustrations may vary from your present
model
1. Handlebars for drive
2. Handlebar for engine brake
3. Choke* or Speed adjust lever**
4. Recoil starter
5. Grass catcher
6. Height adjusting lever
7. Oil cap
8. Deck
9. Sideward guard
10. Spark plug
11. Starter handle
12. Fuel cap
13. Cable clamp
14. Locking lever
15. Speed adjust lever**
16. Self-drive control handle
17. Side discharge channel
18. Mulching wedge
A. Spark plug wrench
* Models without variable speed
** Models with variable speed

Mounting

Unpacking:
Remove the mower from the box by pulling the machine
out form the side
Warning: Ensure that cables are not pinched.
Handlebar and height adjustment: Illustration 3-10
The handlebars are height adjustable. This means that
they can be adjusted so that it best fits you. Before you
install the handlebar, it may be a good idea to have
decided which height is best for you.
1. Set the lower handlebar tube to the working
height that suits you. Attach the wing nut from
the inside of the side bracket and into the
lower handlebar.
2. Attach the upper handlebar on the lower.
Fasten with wing nut from the inside of the
handlebar.
3. Customize cable and secure with cable clamps
Mounting the recoil-starter: Illustration 14-15
1. Pull the engine brake handlebar and hold, in
order to release the starter cord on the engine.
2. Pull gently the starter cord from the engine
(Engine brake handlebar MUST be hold)
3. Attach the starter grip on the rack of
handlebar.
4. Release the engine brake handlebar and the
starter grip.
Mounting the grass collector: Illustration 11-13
1. Click the frame to the grass collector.
The grass collector comes with a handy
indicator showing whether the box is full of
grass and needs emptying.Illustration 32-33
Mulching plug: Illustration 17-19
1. Insert the mulching plug and remove side
discharge guard, if you want to mow with
mulching functionality.
NB Don't use the grass collector
Important: Remember to remove the mulching plug,
when using the grass collector.
Side discharge guard: Illustration 20-23
1. Lift the side guard and insert side discharge
guard. Then insert the mulching plug in rear
discharger to mow with side discharge
function. NB Don't use the grass collector

Cable Adjustment

The following cables may be necessary to readjust:
1. Cable for drive
2. Cable for engine brake
3. Cable for throttle cable
Note: The choke cable cannot be adjusted!
Adjusting the drive cable:
If you experience slack in the drive cable, this can be
solved simply by tighten or loosen the bolt on the cable.
1. Tighten turning clockwise - loosen the cable.
2. Tighten turning anti clockwise - tighten the
cable.
Adjusting the engine brake cable:
If you experience slack in engine brake cable, this can
be solved simply by tighten or loosen the bolt on the
engine block.
Adjusting the throttle cable:
If you experience slack in revolution cable, this can be
solved simply by tighten or loosen the bolt on the
engine block.
7