Identification Of The Parts; Mounting; Tyre Pressure; Battery (Electric Starter) - Texas Rider 6110ES Bedienungsanleitung

Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or
exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Waste electrical products must not be
disposed of with the household waste. This
tool should be taken to your local recycling
centre for safe treatment.
The rider is manufactured according to the latest safety
requirements. These include a blade brake that stops
the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your rider.

Identification of the parts

See Illustration 1+3
Notice: the illustrations may vary from your present
model
A.Choke.
B.Gear.
C.Ignition key - Electric starter.
D.Water nozzle.
E.Height adjustment. (cutting deck)
F.Brake/clutch pedal
G.Parking brake.
H.Coupling rod. (for blade)
I.Safety switch.
K.V-belt
L.Recoil
M.Oil tank
N.Fuel tank
O.Air filter

Mounting

Unpacking: Illustration 5-9
Remove the Rider from the box by following the
description below. The box contains:
1 pcs. Rider
1 pcs. Steering wheel.
1 pcs. Battery Charger
1 pcs. Coupling rod
1 pcs. Seat
1 pcs. Bolt bag (See ill.9 a-l)
The easiest way to unpack:
1. Remove upper frame. If necessary, use a hammer
to remove it from main frame. Get somebody to
hold the end of the frame you can´t reach yourself.
See ill.7
2. Remove the two brackets holding the front wheel
and the rear wheel to the frame. ill. 7-8 (Arrows in
the picture)
3. Remove the rider from the box by pulling the
machine out form the side. It can be an advantage
to be 2 people for this.
Technical installation
Note: To lift the cover, it is necessary to remove all the
black / silver gray handles. (ill.13)
1. Lift the cover (ill.13)
2. Add oil (ill.16) and unleaded 95 octane gasoline
(ill.17)
3. Cennect the wire to the battery (ill.14)
4. Ensure that the safety switch under seat (ill.2) and
on rear plate is activated.
5. Put cover and handles back in place
Assembly instructions
1. Mount the coupling rod for the cutting deck as
shown. (ill.11)
2. Open the seat flap, fit and install the seat as
shown. (ill.10)
3. Mount the steering wheel to steer axle, use a
hammer to knock the pin into the shaft (ill.12)
4. It is recommended to mount the safety bolt and pin
as shown in ill.18 This fix the cover to the chassis
of the machine.

Tyre pressure

Check tyre pressure before start.
The correct tyre pressure is 2.1 bar (31 psi) on all
wheels.
Important: When tyre pressure is too low the valves and
the inner tube may be damaged.

Battery (Electric starter)

Charge the battery before use
Before the electric start function is used, the battery
must be charged for 5 hours. Put the charger plug into
the hole in the battery and connect the charger to a
power supply. Ill.15
Charging during the season
The battery is charged a little during use, buy it will
likely be necessary to charge the battery a couple of
times during the season - depending if the number of
start/stops of the engine. Put it for charging for around 5
hours.
Storage of battery
The battery must always be stored dry and warm during
the winter. Never expose it for low temperatures.
Charge the battery completely before storing and then
place the lawn rider in a place where it is not exposed
to frost. Alternatively cover the battery with a thick
carpet or similar, If the rider is in a shed/garage where
there may be cold.
Charge the battery 1-2 times during the winter (at least
rd
every 3 month) to make sure the battery keeps it full
capacity.
Incorrect storage can damage the battery and is not
covered by warranty.
18