Specifications - Makita 1050D Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Fast charger
5 Knob
6 Scale
7 Pointer
8 Lock-off-button
9 Switch trigger
10 Start
11 End
12 Washer

SPECIFICATIONS

Model
Capacities
Planing width ..................................................... 50 mm
Planing depth .................................................... 0.5 mm
Shiplapping (rabbeting) depth ............................ 15 mm
-1
No load speed (min ) ............................................. 9,000
Overall length ..................................................... 293 mm
Net weight ...............................................................2.1 kg
Rated voltage ....................................................D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
Explanation of general view
13 Thumb screw (A)
14 Edge fence (Guide rule)
15 Thumb screw (B)
16 Blade edge
17 Side of drum
18 Cutting line
19 "V" groove
20 Front base
21 Align "V" groove with edge of
workpiece
22 Dust bag
23 Nozzle
10. Do not disassemble charger or battery cartridge;
1050D
11. To reduce risk of electric shock, unplug charger
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
14. If operating time has become excessively
15. If electrolyte gets into your eyes, rinse them out
ADDITIONAL SAFETY RULES FOR CHARGER
ENC001-3
& BATTERY CARTRIDGE
1.
2.
3.
4.
5.
6.
7.
24 Fastener
25 Installation bolts
26 Hex wrench
27 Loosen (counterclockwise)
28 Planer blade
29 Drum
30 Drum cover
31 Pan head screws
32 Pan head screw
33 Set plate
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as nails,
coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
5