Stiga TITAN Road kit Montageanleitung Seite 17

3. Assemble the following in the ramp:
• Upper edging (6:X).
• The sign (7:S) if necessary.
4.4 Control
Assemble the control front right as described
below:
1. Remove the black cover washer in the steering
pulpet.
2. The bracket (8:I) and the control (8:H) are
delivered assembled. Separate these.
3. Assemble the bracket (8:I) for the control (8:H).
Use two screws, threaded direct into the
steering pulpet.
4. Insert the cable into the pulpet and fit the cable
grommet into the hole.
5. Draw up the rubber protecting at the control and
fasten with 4 screws and 4 nuts.
4.5 Horn
Loosen the screw, remove the nut and assemble the
horn (9:J). Check that the horn doesn´t touch any
part of the machine. Tighten the screw and the nut.
4.6 Harnesses
The harnesses are never allowed to
touch moving or hot parts. Risk of
shortcircuit and fire.
1. Disassemble the following from the machine:
• The steering pulpet rear cover.
• The elecrtrical center cover.
• The right motor casing.
• Front and rear motor casings.
2. Assemble the front harness (10:N).
3. Assemble the rear harness (11:M). Assemble
the cable grommet in the upper motor casing.
4. Attach the harnesses by bundle strips at the
following places:
• At the front under, fit against the hydraul
hoses/body.
• Under the seat, fit against the lower part of
the ROPS.
• Along the protective frame to the headlights.
The harness shall be located at the inside of
the ROPS.
• Under the cooler, fit against other harnesses.
• In front of the air filter, fit against other
harnesses.
5. Connect the following plugs:
•
Licence plate illumination
• Between front and rear harnesses at the
electrical central.
• Headlights at the ROPS.
• 2 tabs to the horn.
• Between front harness and the control.
ENGLISH
6. Connect the rear lights according to a separate
7. When all actual cables are connected to the
8. Connect the ground cable (12:T).
4.7 Trailer socket
Assemble the trailer socket (13:F) as described
below.
1. Check that the hole (13:V) is 40 mm in
2. Place the cable with connecting device and
3. Assemble the cover against the rubber sealing
4. Fix the cable with bundle strips against other
4.8 Fuse box, connecting
1. Loosen the distribution box's mounting plate by
2. Assemble the enclosed fuse carrier (15:G) with
3. Connect the cable (marked +30) from the
4. Assemble the direction indicator
5. Reassemble the distribution box's mounting
4.9 Reassembly
1. Reset the power by the main switch.
2. Reassemble all covers and casings.
4.10Light adjustment
The headlights are equipped only with dimmed
headlights. These shall be adjusted according to
local regulations. See fig. 17 for a guiding value.
4.11Signs and reflexes
at the rear.
Fit the reflexes (16:R) at the rear bumper.
The signs (16:Q) shall be assembles at the rear and
left motor casings and at the backrest according to
the local regulations.
GGP reserves the right to make alterations to the
product without prior notification.
enclosed instruction
Connect cable X3 to the left backlight.
Connect cable X6 to the right backlight.
lamps, fitted to the ramp, the cables shall be
fastened to the ramp lower part with bundle
strips.
diameter. If not, drill up the hole to 40 mm.
rubber sealing, pointing backwards in the hole
in the frame.
and into the frame with 3 screws and nuts.
harnesses at the rear engine bracket.
removing the 2 screws (14:U) and fold out the
plate.
mounting plate to the distribution box's
mounting plate (ev. drill necessary holes).
enclosed fuse box to terminal 8 in the machine's
fuse box. See fig. 14. Note that the machine can
be equipped with two alternative fuse boxes,
Alt. 1 and Alt. 2.
and the light relay (15:L) with attachments (ev.
drill necessary holes).
plate.
EN
15:K)
relay
17