Displaying Messages; Time-Controlled Display; System Settings; Setting Date And Time - IMG STAGE LINE PML-60R Bedienungsanleitung

4.1.5 Displaying messages

GB
To display one or multiple messages that have
been saved:
1) If the date/time display is active, press the but-
ton [ESC] to deactivate it.
2) Press the button [RUN-PAGE].
3) Use the buttons [A] to [Z] to enter the storage
locations of the messages in the order in which
they are to appear on the display. Use the but-
ton [DEL] to correct wrong entries.
4) Press [ENTER] to complete the entry.
All messages selected are briefly displayed and
then repeatedly appear on the display according to
the parameters that have been defined. If a storage
location does not contain any message, the error
message "EMPTY Page" will be displayed.

4.1.6 Time-controlled display

Five independent programs allow for the automatic
display of saved messages at specific times. To
create a program:
1) If the date/time display is active, press the but-
ton [ESC] to deactivate it.
2) Press the button [PROG]. "PROG ( / / / )" is
displayed.
3) Press [ ] twice. The program location "SCH A"
is displayed.
4) Press [ ]. "A" is displayed in bold.
5) Press [ ] or [ ] to select the storage location
(A to E) and then press [ENTER] to confirm.
"SYR00" (= starting year) is displayed.
6) Set the year for the start time. Press [ ] or [ ]
to set the individual digits and press [ ] or [ ]
to go to another position. Press [ENTER] to
confirm.
Proceed in the same way to enter the month
"SMO", the day "SDY", the hour "SHR" and the
minute "SMI" for the start time.
Then proceed in the same way to enter the
year "TYR", the month "TMO", the day "TDY",
the hour "THR" and the minute "TMI" which
define the point of time until which the display is
to be shown.
7) An asterisk
to [Z] to enter the storage locations of the mes-
sages in the order in which they are to appear
on the display. Use the button [DEL] to correct
wrong entries.
8) Press [ENTER] to complete the entry.
20
is displayed. Use the buttons [A]

4.1.7 System settings

4.1.7.1 Setting date and time

1) If the date/time display is active, press the but-
ton [ESC] to deactivate it.
2) Press the button [FUNCT]. "SETUP (
displayed.
3) Press [ ] repeatedly until "YR:" is displayed.
4) To change the number of the year, press [ ].
Set the number of the year. Press [ ] or [ ] to set
the individual digits and press [ ] or [ ] to go to
another position. Press [ENTER] to confirm.
5) Press [ ]; "MTH" is displayed. To change the
month, press [ ], set the month and then press
[ENTER] to confirm.
6) Press [ ]; "DAY" is displayed. To change the
day, press [ ], set the day and then press
[ENTER] to confirm.
7) Press [ ]; "HR:" is displayed. To change the
hour, press [ ], set the hour and then press
[ENTER] to confirm.
8) Press [ ]; "MIN" is displayed. To change the
minute, press [ ], set the minute and then press
[ENTER] to confirm.
9) Press [ESC] to exit the setting menu.
The setting can be cancelled at any time with
[ESC].

4.1.7.2 Changing the brightness

1) If the date / time display is active, press the but-
ton [ESC] to deactivate it.
2) Press [FUNCT]. "SETUP (
3) Press [ ] repeatedly until "BR:" is displayed.
4) To change the brightness, press [ ]. Press [ ]
or [ ] to select the brightness: A = 100 %,
B = 75 %, C = 50 %, D = 25 %
Press [ENTER] to confirm.
5) Press [ESC] to exit the setting menu.
The setting can be cancelled at any time with
[ESC].

4.1.7.3 Changing the unit address (IP)

To distinguish multiple units, each unit may be
assigned an individual ID / address:
1) If the date/time display is active, press the but-
ton [ESC] to deactivate it.
2) Press the button [FUNCT]. "SETUP (
displayed.
3) Press [ ] repeatedly until "ADD" along with the
current address is displayed.
)" is
)" is displayed.
)" is