Telefunken TRC 850 Bedienungsanleitung Seite 22

Timer Setup
Timer Sleeptim.
Set
Setup TV
Timer X
Setup
X= 1, 2, 3, 4 or
The LCD remote can be programmed with 2 different kind of Timer, these are:
• A TV Sleep Timer. At the end of the set Timer period, the LCD remote
sends the Power command for the TV Mode device. The TV Sleep
Timer can be set for a period of 1-90 minutes. The "Z
displayed when a TV Sleep Timer is set.
• 4 Timers that can send a sequence of up to 4 key commands at
the preset time. (i.e.: selection of a different channel);
the Bell symbol is displayed on the LCD screen.
To set a TV Sleep Timer (no "Z
a. Turn on the TV Mode device.
b. Press and hold Setup key until "CODE SETUP" is displayed (takes approximately 2-3 seconds).
c. Release Setup key.
d. Navigate to "TIMER SETUP" by pressing the Setup key 2 times. Press and release OK key.
e. "SLEEPTIM.TV" is displayed. Press and release the OK key.
f. "TV-TIMER EINST" is displayed. Press and release the OK key.
g. "MINUTEN EINST" is displayed with "minutes" flashing. Use the Up/Down keys to set the
minutes then press and release the OK key.
h. "FERTIG" will be displayed and the remote will remain in Setup, returning to the "CODE
SETUP" screen.
i. Press and release Exit key to return to normal operation. Leave the remote pointing at the
TV device.
To clear a TV Sleep Timer ("Z
a. Press and hold Setup key until "CODE SETUP" is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to "TIMER SETUP" by pressing the Setup key 2 times. Press and release OK key.
d. "SLEEPTIM.TV" is displayed. Press and release the OK key.
e. "TV-TIMER AUS" is displayed. Press and release the OK key.
f. "AUS BEST." is displayed. Press and release the OK key.
g. "FERTIG" will be displayed and the remote will remain in Setup, returning to the
"CODE SETUP" screen.
Setting and Clearing Timers
The LCD remote can be programmed with up to 4 Timers (Timer1, 2, 3 & 4). Each Timer can be
assigned up to 4 keys to activate at the set time (e.g. to change SAT Mode channel to 123 at
22:35). The first key must always be a Mode key. Subsequent keys cannot include Up, Down,
Left, Right, OK, Exit, Setup or any Mode key. Timers can only be set to activate within the
following 24-hour period. Timers are automatically cleared after activation. The "Timer Bell"
symbol is displayed when any Timer is set.
To set a Timer
(Note the Timer must be cleared first if it was previously set – see To Clear a Timer below)
a. Press and hold Setup key until "CODE SETUP" is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to "TIMER SETUP" by pressing the Setup key 2 times. Press and release OK key.
d. "SLEEPTIM.TV" is displayed.
e. Navigate to "TIMER X SETUP" (where "X" is 1, 2, 3 or 4). Press and release the OK key.
f. "Timer X EINST" is displayed. Press and release the OK key.
g. "Timer X ZEIT?" is displayed with the "hours" flashing. Use the Up/Down keys to set the hours
then press and release the OK key.
22
TV-Timer Minuten
Set Set
Einst Einst
or
TV-Timer Aus
Set
Aus Best.
Z
zz
Timer X Timer X
Set Set
Einst Zeit? 23:58
Timer X Aus
Set
Aus Best.
" in normal display)
Z
Z
" in normal display)
Z
Z
Fertig
Set Set
10
Z
zz
Fertig
Set Set
Z
zz
Timer X Timer X...
Set Set
Mod. Eingy
X= 1, 2, 3, 4
Y= 1, 2, 3
Fertig
Set Set
" symbol is
Z
Z
Fertig
Set Set
DVD
Mon 23:58
Z
z
DVD
Mon 23:58
z